manualshive.com logo in svg

Mercury Racing QC4V 1350, Инструкция по эксплуатации, техническому обслуживанию и гарантии, Страница: 55 / 73

Поделиться
Скачать
Mercury Racing QC4V 1350 Скачать руководство пользователя страница 55

6 - M

AINTENANCE

90-8M0077672   JUNE  2013

51

1
2
3
4
5
6
7
8
9

3. Align splines and install propeller, washer and propeller nuts.

a -

Nylon insert nut

b -

Thin nut

c -

Washer

d -

Bushing

e -

Retaining ring

Tube

Ref No.

Description

Where Used

Part No.

Extreme

Grease

Propshaft

8M0071842

4. Place wood block between the propeller blade and

anti‑ventilation plate to prevent rotation and tighten the

propeller nuts. After first use, re‑tighten the propeller nuts.

Check the propeller at least every 20 hours of operation.

Description

Nm

lb. in.

lb. ft.

Propeller nuts

136

–

100

a

b

c

d

e

45780

F

LUSHING

 C

OOLING

 S

YSTEM

!

 WARNING

Rotating  propellers  can  cause  serious  injury  or  death.  Never

operate the boat out of the water with a propeller installed. Before

installing  or  removing  a  propeller,  place  the  drive  unit  in  neutral

and  engage  the  lanyard  stop  switch  to  prevent  the  engine  from

starting. Place a block of wood between the propeller blade and

the anti‑ventilation plate.

NOTICE

Operating  the  engine  out  of  the  water  at  high  speeds  creates

suction, which can collapse the water supply hose and overheat

the engine. Do not operate the engine above 1400 RPM out of the

water and without sufficient cooling water supply.

To prevent silt and salt buildup in the cooling system, flush with

freshwater.

1. Install a flushing hose from a water tap to the flushing

connector. Consult your boat owners manual for the location

of the flushing connector.

2. Completely open the water tap. Place the remote control in

neutral position and start the engine. Operate the engine at

idle speed, in neutral, for about 10 minutes or until discharge

water is clear. Stop the engine, shut off the water, and remove

the flushing hose.

Содержание QC4V 1350










































































Отзывы:

Нет отзывов