manualshive.com logo in svg

Mercury Racing QC4V 1350, Инструкция по эксплуатации, техническому обслуживанию и гарантии, Страница: 48 / 73

Поделиться
Скачать
Mercury Racing QC4V 1350 Скачать руководство пользователя страница 48

6 - M

AINTENANCE

 

44

90-8M0077672   JUNE  2013

Tube Ref

No.

Description

Where Used

Part No.

87

High

Performance

Gear Lubricant

Transom input shaft bearing

housing

92-858064K01

C

HECKING

 M8 

OR

 NXT6 SSM D

RIVE

 U

NIT

 F

LUID

 L

EVEL

1. Remove the upper vent plug from the gearcase. The gear

lubricant level should be to the bottom of the vent plug hole

with the propeller shaft level.

2. If gear lubricant level is low, add fluid until gear lubricant

comes out of the vent plug opening.

3. Install the vent plug.

a -

Vent plug opening

a

b

45697

b -

Level propeller shaft

IMPORTANT: If the lubricant color is green, service the drive with

High Performance Gear Lubricant. If the fluid color is amber, service

the drive with Mercury Racing Gear Oil.

Tube Ref

No.

Description

Where Used

Part No.

87

High

Performance

Gear Lubricant

M8 drive unit

92-858064K01

SAE 85W-90

Mercury Racing

Gear Oil

M8 drive unit

8M0078015

C

HECKING

 T

RANSMISSION

 F

LUID

 L

EVEL

The transmission must be level to check the fluid level in the

transmission.

1. Start the engine, and shift the transmission through the

FORWARD, REVERSE, and NEUTRAL positions: shut off the

engine.

2. Remove the dipstick and check the fluid level against the

markings on the measure.

3. Add fluid (Type F

1.

, ATF) in 200 cc (½ pint) intervals until the

level is at, or just below the FULL mark, do not overfill.

C

LOSED

 C

OOLING

 S

YSTEM

The fluid in the coolant reservoir should be maintained at

approximately 6 mm (¼ in.) above the baffle plate.

1.

Use type FA only if type F is not available

Содержание QC4V 1350










































































Отзывы:

Нет отзывов