manualshive.com logo in svg

Mercury Racing QC4V 1350, Инструкция по эксплуатации, техническому обслуживанию и гарантии, Страница: 35 / 73

Поделиться
Скачать
Mercury Racing QC4V 1350 Скачать руководство пользователя страница 35

4 - O

PERATION

90-8M0077672   JUNE  2013

31

1
2
3
4
5
6
7
8
9

S

TARTING

, S

HIFTING

, 

AND

 S

TOPPING

!

 WARNING

Explosive fumes contained in the engine compartment can cause

serious injury or death from fire or explosion. Before starting the

engine, operate the bilge blower or vent the engine compartment

for at least five minutes.

N

EW

 E

NGINES

 

OR

 E

NGINES

 C

OMING

 O

UT

 

OF

 S

TORAGE

Refer to 

Recommissioning the Power Package.

IMPORTANT: Observe the following:

•

Do not start the engine without supplying water to the

seawater pickup pump (to prevent pump or engine damage).

•

Never shift the drive unit unless the engine is at idle RPM.

Perform the following as appropriate:

Check all items listed in 

Operation Chart.

Perform any other necessary checks, as indicated by your

dealer, or specified in your boat owner's manual.
Place the drive unit in the full down/in position.

Place the control handle in neutral.

C

OLD

 

OR

 W

ARM

 E

NGINE

EFI engines require no throttle advance to start. The boat can be

operated after the engine has started and is idling smoothly.
NOTE: Engines that have not been started for extended periods or

have had fuel filter changes may not stay running on the first few

initial attempts to start. Do not advance the throttle to keep the

engine running. Continue to restart the engine until it idles smoothly,

which means the fuel system is primed. Allow the engine to warm up

to 54 °C (130 °F) before advancing the throttle. Do not operate at

full throttle until the engine reaches an oil temperature of 60 °C

(140 °F).

F

LOODED

 E

NGINE

Before trying a restart, check for full battery voltage (13.8–14.2

volts). Move control/throttle lever to full throttle. Be prepared to

decrease the engine speed to idle as soon as the engine starts.

S

TARTING

 

PROCEDURE

1. Turn the key switch to "START." Release the key and allow

the switch to return to the "RUN" position.

2. Check the oil pressure gauge immediately after the engine

starts. If oil pressure is below the minimum requirement, see

Specifications

, stop the engine immediately, and determine

the cause.

3. If the engine is cold, make sure the engine is idling smoothly

before operating the boat.

4. Check the coolant temperature gauge to ensure that the

engine temperature is not abnormally high. If it is, stop the

engine immediately and determine the cause.

5. Ensure that the charging system is functioning correctly.
6. Observe the power package for fuel, oil, water, and exhaust

leaks.

O

PERATION

 C

HART

1.

Before Starting

Open the engine hatch.

Содержание QC4V 1350










































































Отзывы:

Нет отзывов