Mercia Garden Products 01DTSHOSBRAX0604SDFW-V1, Общее руководство по инструкции

Страница: 2 / 11

17
18 19
20
21 22
50mm Screw x 46
20mm Screw x 8
40mm Screw x 34
30mm Screw x 88
60mm Screw x 10
Felt Tacks x 66
23
24
P 2
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-
driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
LOCATION FOR YOUR GARDEN BUILDING
A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,
annual treatment and to allow air flow around the building.
Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing
damage to the building.
TIMBER
As with all natural materials, timber can be affected during various weather conditions. For the duration of heavy
or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during
excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be
helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine
and sheltered as much as possible during rain or snow.
Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent
the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.
Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-
ment to prevent water ingress
Pressure Treated buildings - Require a waterproof treatment to prevent water ingress
Log Cabins - Are supplied untreated and require a preservative and waterproofing treatment.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on firm ground, to prevent distortion. Refer to diagrams for the base
dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding
should overlap the base, creating a run off for water. It is also recommended that the floor be at least 25mm above
the surrounding ground level to avoid flooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or
using this product.
01DTSHOSBRAX0604SDFW-V1
Overall Dimensions:
Width = 1318mm
Depth = 1842mm
Height = 2087mm
Base Dimensions:
Width = 1175mm
Depth = 1753mm
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Nail Bag
There may be extra screws present in the nail bag
The building that you have purchased can be built
as an Apex or a Reverse Apex. Also you can choose
in which arrangement you wish to have your panels
set up. See these images on display to give you an
idea of which set up is most suitable for you.
2 1 3
4
5 6 7
Door Panel QTY 1
AI-01S11SHSD1180X1802-V1
Plain Panel 1 QTY 2
AI-S11SHPPTF524X1802-V1
Plain Panel 2 QTY 2
AI-S11SHPPTF1180X1802-V1
Door QTY 1
AI-S11FBMBZBD743X1680-V1
Roof QTY 2
AI-S11OSBOHAR715X1794-V1
Floor QTY 1
AI-R11OSBF1175X1753-V1
Gable Top QTY 2
AI-S11SHAGT1180X262-V1
9
Door Beading Strip 12x28x1590mm QTY 2
S1228-1590mm
10
Cover Trims 12x40x1792mm QTY6
S1240-1792mm
11
Fascias 12x60x690mm QTY 4
S1260-690mm
12
Door Block 28x28x150mm QTY 1
FS2828-150mm
13
Ridge Bar 28x28x1704mm QTY 1
FS2828-1704mm
14
Window Strip 12x28x550mm QTY 4
S1228-550mm
15
Window Cover trims 12x40x513mm QTY 3
S1240-513mm
16
Window Cover trims 12x40x1180mm QTY 1
S1240-1180mm
Shed diamond
Finial QTY 2
Shed diamond Finial
Corner Brace QTY 2
PI-07-0012
T-Hinge QTY 3
PI-07-0021
Turn Button QTY 2
PI-07-0034
Felt QTY 1
PI-01-0013
Pad Bolt QTY 1
PI-07-0035
Window Panel QTY 1
AI-01S11SH2CW1180X1802-V1
8
Styrene QTY 2
PI-05-0114
Cilled Window QTY 1
PI-08-0013