manualshive.com logo in svg

Mercedes-Benz 171.456 2005, Руководство по установке

Поделиться
Скачать
Mercedes-Benz 171.456 2005 Скачать руководство пользователя страница 8

 

3.  Connect the MOST adapter connector to 

the MHI control module (A, Figure 16). 

4.  Connect the MHI power supply connector to 

the MHI control module (B, Figure 16). 

5.  Connect the MHI microphone array 

connector (C, Figure 16) to the Tele Aid 
microphone connector (D, Figure 16). 

6.  Organize and wire tie loose cabling. 

 

Figure 16                                                      

P82.70-xxxx-71

 

7.  Connect the telephone FAKRA female, 

black connector to the antenna switch jack 
labeled “BOOSTER” (A, Figure 17). 

8.  Connect the Tele Aid FAKRA female, white 

connector to the antenna switch jack 
labeled “LCT” (B, Figure 17). 

9.  Connect the main antenna FAKRA male, 

white connector to the antenna switch jack 
labeled “ANTENNA” (C, Figure 17). 

10.  Connect the 2-pin power supply connector 

to the antenna switch (D, Figure 17). 

 

Figure 17                                                      

P82.70-xxxx-71

 

 

 

PRELIMINARY DRAFT

 November 2004

 

8 

Содержание 171.456 2005
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды