background image

 

 

Installation Instructions

 

Date:

 

November 2004

 

 

Order No.:

 

PRELIMINARY DRAFT 

 

Supersedes:

 

 

 

Group:

 

82

 

 

SUBJECT

:

 

MODEL 171.456/473 

MODEL YEAR 2005 

CELLULAR TELEPHONE INSTALLATION

 

 
 

We are interested in your comments and/or suggestions regarding these installation instructions—
please e-mail them to 

[email protected] 

 
 

WARNING

 

Do not disconnect the negative battery cable. Extensive reprogramming requirements will 
otherwise be necessary. Wiring harnesses will be electrically active. It is therefore necessary to 
exercise extreme caution while executing these installation instructions. Failure to do so could 
result in severe vehicle damage, personal injury, or death from electrical shock. Keep the ignition 
and radio powered OFF through the final test.

 

 
 

MOST Notes 

  Optical fibers damage easily; handle optical fibers with care to prevent cuts, nicks, abrasions, kinks, 

and crushing. 

  Minimum bend radius for optical fibers is 25 mm. 

  Optical fiber “ring configurations” must form a closed loop to function (i.e. couple the input of a 

component with the output of the preceding component). 

  Identify MOST optical fibers cables by their orange or yellow, semi-rigid insulation. 

  Electromagnetic interference (EMI) from bundled vehicle electrical harnesses does not affect optical 

fibers. 

 
 

 

This bulletin has been created and maintained in accordance with MBUSA-SLP S423QH001, Document and Data Control, and MBUSA-
SLP S424HH001, Control of Records.  

 

 

 

© 2004 Mercedes-Benz USA, LLC. 

All rights reserved. Reproduction or translation in whole 

Mercedes-Benz Canada, Inc. 

or in part is not permitted without authorization from the 

Dealer Workshop Services 

publisher. Printed in U.S.A. 

www.MBUSA.com 

            

1-800-FOR-MERCedes 

www.startekinfo.com

 

Содержание 171.456 2005
















Отзывы: