manualshive.com logo in svg

Mendota FV33i-PF2-0113, Инструкция по установке и эксплуатации

Поделиться
Скачать
Mendota FV33i-PF2-0113 Скачать руководство пользователя страница 43

42 

 

8.

 

Before reinstalling burners, loosen the screw that secures the rotary air shutter on the Front Burner. Rotate the air shutter 
open to ¼” minimum. 

 
9.

 

Install both rear and front burners in 
their original locations and positions 
and secure down using screws you 
removed earlier. 

 
 
 
 
 
 
 
 
 
 
 
 
10.

 

Make certain front burner is running 
parallel to front face of unit positioned properly so that the pilot light hood pointing to the left is pointed properly to-
wards the burner’s flame propagation ports. 

11.

 

Make certain Rear Burner is positioned properly so that the pilot light hood pointing to the left is pointed properly to-
wards the burner’s flame propagation holes. 

 
 
 
 
 
 
 
 
 
 
 

  

FRONT BURNER SHUTTER ADJUSTMENT

LOOSEN SCREW

ROTATE SHUTTER OPEN

-1/4" MINIMUM-

FRONT

BURNER

REAR

BURNER

PILOT LIGHT FLAMES 

MUST OVERLAP 

BURNER PORTS.

Содержание FV33i-PF2-0113































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды