manualshive.com logo in svg

Mendota FV33i-PF2-0113, Инструкция по установке и эксплуатации

Поделиться
Скачать
Mendota FV33i-PF2-0113 Скачать руководство пользователя страница 35

34 

REMOTE TRANSMITTER OPERATING INSTRUCTIONS  

TO TURN ON THE APPLIANCE: 

1.  Press the ON/OFF button.  The transmitter display will show all active icons on the screen.

 

 

2.  Select the Thermostat Mode by pressing the Thermostat Key: OFF (meaning Manual Mode), ON (meaning 

normal Thermostat) or Smart (meaning Smart Mode). 
a.  In OFF (Manual Mode), the appliance will ignite and start on HI. 
b.  In ON (Normal Thermostat Mode), the appliance will only ignite if the Set Temperature is greater than the 

Room Temperature. 

c.  In SMART (Smart Mode), the appliance will only ignite if the Set Temperature is greater than the Room 

Temperature. 

TO TURN OFF THE APPLIANCE, press the ON/OFF button. 

 

MODE KEY: 

Pressing the MODE KEY toggles between the 

various available functions: Flame Height, Fan Speed, Accent 
Light Dimmer and Secondary Burner On/Off. 

 

Flame Height: 

6 flame height Levels are available. While the Flame 

Height Icon is displayed, pressing the Up or Down button 
once will increase or decrease the flame height by 1 of 6 in-
crements. If the flame height is at Level 1 and the Down but-
ton is pressed, all burners will turn OFF. If in IPI mode, the 
pilot light will also extinguish. If in Standing Pilot Mode, the 
pilot light will remain ON. Note: If in SMART model, the flame 
height function is not available for manual adjustment. In 

SMART mode, the flame height regulates automatically.  
 

 

Fan Speed Control: 

The fan speed can be adjusted through six (6) speeds and 

OFF.  To activate this function, press the MODE Key to index to the 
fan control icon. Use the UP/Down Arrow Key to turn ON, OFF or 
adjust the fan speed. A single “beep” will confirm reception of the 
command. Once you set the desired fan control, the system will re-
member your selected fan speed until you manually change it. 

 

Accent-Light Dimmer: 

This function controls the Mendota Accent Light functions. 

Pressing the UP key in this mode will TURN ON the Accent Light and 
allow you to control the brightness of the Accent Light in 6 steps. A 
single “beep” will confirm reception of the command.  Once you set 
the desired light brightness, the system will remember your selected 
brightness level until you manually change it.

 

Secondary Burner: 

This function controls the Secondary Burner’s 

ON/OFF feature. Pressing the UP Key in this mode will TURN ON 
the Secondary Burner and Pressing the DOWN Key will TURN OFF 
the Secondary Burner. The flame level will not change when you turn 
the Secondary Burner On or Off. The flame level can only be 

changed in the Flame Level mode. 

 

NOTE: The “AUX” function is not available and shall be skipped over.

Содержание FV33i-PF2-0113































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды