background image

D33340 | Date 08/2017  

7

 Safety regulations

1.2  

 Product safety and  dangers

The appliances described in this manual are technically sophisticated, manufactured using 

high-quality materials and subject to many hours of testing in the factory. They contain the 

latest technology and comply with recognised technical safety regulations. However, there are 

still risks involved, even when the appliances are used as intended. These are described below.

Warning!

After removing covers, live parts may be exposed. You may receive 

an electric shock if you touch these parts. Disconnect the mains plug 

before removing any covers. Only electrical technicians may work on 

the electrical equipment of the appliances.

Warning!

When loading the appliance with an unsuitable load, poisonous or 

explosive vapours or gases may be produced. This could cause the 

appliance to explode, and people could be severely injured or poi-

soned. The appliance may only be loaded with materials/test objects 

which do not form any toxic or explosive vapours when heated up 

(see also chapter Intended use on page 8).

Warning!

If the door is open while the appliance is in operation, the appliance 

may overheat and pose a 

fi

 re hazard. Do not leave the door open 

during operation.

Warning!

Depending on operation, the surfaces in the working chamber 

and the chamber load may still be very hot after the appliance is 

switched off. Touching these surfaces can cause burns. Wear heat-

resistant protective gloves or wait until the appliance cools down. 

Warning!

In case of appliances of a certain size, you can get accidentally 

locked in, which is life-threatening. Do not climb into the appliance!

1.3  Requirements of the   operating personnel

The appliance may only be operated and maintained by persons who are of legal age and 

have been instructed accordingly. Personnel who are to be trained, instructed or who are un-

dergoing general training may only work with the appliance under the continuous supervision 

of an experienced person.
Repairs may only be performed by qualified electricians. The regulations in the separate service 

manual must be observed.

Содержание SF PLUS Series

































































Отзывы: