Meltem InControl Скачать руководство пользователя страница 4

Installation manual 

M-WRG-S/Z-T(-F, -FC)

- 4 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L AT I O N   &   H E AT   R E C O V E R Y

1.3 

Target group

The activities described in this manual must only be carried out by technicians with the following 

qualifications:

 

Training in the installation and commissioning of electrical devices

 

Training in electrical hazards and the local safety requirements

 

Knowledge of the relevant standards and directives

 

Knowledge and observance of this document and all the safety instructions

1.4 

Revision index

Edition

Manual

Date

1

st

 edition

Installation manual M-WRG-S/Z-T(-F, -FC)

Week 50/2015 EN

1.5 

Explanation of the symbols used

 

This symbol indicates an action to be taken.

 

This symbol indicates a list.

1.6 

Supplementary documents

Manual

Part no.

Installation manual M-WRG-S.../M-WRG-K...

5300-10-01

2  Safety instructions

This manual contains notes that you must follow for your own personal safety and to avoid injury 

and damage to property. They are highlighted by warning triangles and are shown as follows ac-

cording to the level of danger.

2.1 

Hazard classification

DANGER

The signal word designates a hazard with a 

high

 degree of risk which, if it is not avoided, will result 

in death or severe injury.

WARNING

The signal word designates a hazard with a 

medium

 degree of risk which, if it is not avoided, will 

result in death or severe injury.

CAUTION

The signal word designates a hazard with a 

low

 degree of risk which, if it is not avoided, could 

result in minor or moderate injury.

NOTE

A note as used in this manual contains important information about the product or about a part of 

the manual to which particular attention should be paid.

Содержание InControl













Отзывы: