Meltem 5016-1-1 Скачать руководство пользователя страница 28

Страница: 28 / 32

Operating instructions

M-WRG-S/Z-T(-F,-FC) / M-WRG-S/Z-T(-F,-FC)-FU ventilation unit

- 28 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L AT I O N & H E AT R E C O V E R Y

12 Cleaning

WARNING

►

Switch off the power to the ventilation unit before cleaning.

►

When cleaning, make sure that no moisture penetrates into the inside of the housing.

►

Never use a high pressure cleaner, steam cleaner or steam jet.

The ventilation unit is made of high quality plastic and requires little care.

►

Wipe the outer surfaces from time to time with a soft, damp cloth. Use mild soapy water. A

commercially available plastic cleaner can be used for particularly stubborn dirt.

NOTE

►

Never use acidic, corrosive or abrasive cleaning agents.

13 Troubleshooting

Error

Cause

Remedy

Ventilation unit is not running

Ventilation unit is in safe mode

after an EMC fault

Switch the ventilation unit off,

wait 15 s, then switch on

Installation error

Have the wiring checked by a

qualified electrician

Faulty switch, motor or control-

ler

Check by a qualified electrician

Air flaps do not open after

switching on

After a long stoppage or when

starting up for the first time, the

servomotor is not powered by

the electronic circuit.

Switch the ventilation unit off

and on again

Air flap range of motion is

blocked by foreign bodies

(plaster, polystyrene, etc.)

Carefully remove the foreign

bodies, remove the cover if

necessary (see „11.3.1 Re-

move cover from ventilation

unit“ on page 26)

Ventilation unit starts to chirp

at intervals

Filter is dirty

Change the filter (see „11.3

Filter change“ on page 25)

The ventilation unit frequently

activates the frost protection

function
All the LEDs on the InControl

pushbutton sensor flash

Wiring error

Have the wiring checked by a

qualified electrician

Содержание 5016-1-1

































Результаты поиска

Содержание 5016-1-1

Отзывы:

Похожие инструкции для 5016-1-1

Бренды по названию

Популярные бренды

Meltem 5016-1-1, Руководство по установке

Результаты поиска

Содержание 5016-1-1

Отзывы:

Похожие инструкции для 5016-1-1

Бренды по названию

Популярные бренды