Melon Slice Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 30

Melon Slice Скачать руководство пользователя страница 6

2. Wheels and Tires

• Check tire pressure is as recommended according to the

speciﬁ cation displayed on the tire sidewall

• Check tires for tread and ensure they do not have any

bulges or excessive wear.

• Check all wheel spokes are ﬁ rm and are intact
• Check rims run true and are without any obvious buckles

or kinks

• Check that axle nuts are tight. For bicycles equipped

with quick release axles, ensure locking levers are ten-
sioned appropriately and in the closed position.

3. Saddle

• Check the clamp underneath the saddle is ﬁ rmly secured

to the saddle post

• Check frame clamping mechanism is tightly fastened
• Ensure that the minimum insertion mark cannot be seen

on the saddle pillar

4. Steering

• Check that the handlebar and stem enable correct

steering and are properly adjusted and tightened

• Check that the setting of the handlebars is correct in

relation to the forks and the direction of travel

• Check the head set locking mechanism is appropriately

ﬁ xed and fastened

• If handlebar extensions are ﬁ tted check they are posi-

tioned and secured correctly

• Ensure the minimum insertion mark cannot be seen on

the handlebar stem

• Ensure the ends of the handlebars and bar ends are

covered or capped

.

5. Chain

• Check the chain is lubricated, clean and runs freely
• In wet or dusty conditions service the chain more fre-

quently

6

WARNING:

The reﬂ ectors and the reﬂ ector mounting brackets
must not be removed from your bicycle. Doing so
may reduce your visibility to other road users, po-
tentially jeopardizing your safety. Serious injury or
death may result if you are hit by another vehicle
unable to see you.

WARNING:

Reﬂ ectors should always be used in conjunction
with powered lighting when riding at night, at
dawn, dusk, or at any other time in poor visibility.
Failure to do so is dangerous and may result in
serious injury or death.

When riding at night, in addition to the reﬂ ectors, the
bicycle should also be equipped with powered lights. Re-
ﬂ ective tape on the rider’s clothing is also recommended to
increase visibility.

55

«
...
4
5
6
7
8
...
»

Содержание Slice































Отзывы:

Нет отзывов