Mellanox Technologies Innova IPsec Скачать руководство пользователя страница 61

Страница: 61 / 68

Rev 1.8

Mellanox Technologies

Appendix C:

Safety Warnings

1. Installation Instructions

2. Over-temperature

3. During Lightning - Electrical Hazard

4. Copper Cable Connecting/Disconnecting

5. Equipment Installation

6. Equipment Disposal

7. Local and National Electrical Codes

Read all installation instructions before connecting the equipment to the power source.

This equipment should not be operated in an area with an ambient temperature exceed-
ing the maximum recommended: 55°C (131°F).

To guarantee proper air flow, allow at least 8cm (3 inches) of clearance around the ven-
tilation openings.

During periods of lightning activity, do not work on the equipment or connect or dis-
connect cables.

Some copper cables are heavy and not flexible, as such they should be carefully
attached to or detached from the connectors. Refer to the cable manufacturer for spe-
cial warnings and instructions.

This equipment should be installed, replaced, or serviced only by trained and qualified
personnel.

Disposal of this equipment should be in accordance to all national laws and regula-
tions.

This equipment should be installed in compliance with local and national electrical
codes.

Содержание Innova IPsec





































































Результаты поиска

Содержание Innova IPsec

Отзывы:

Похожие инструкции для Innova IPsec

Бренды по названию

Популярные бренды

Mellanox Technologies Innova IPsec, Руководство пользователя

Результаты поиска

Содержание Innova IPsec

Отзывы:

Похожие инструкции для Innova IPsec

Бренды по названию

Популярные бренды