Med-Mizer ActiveCare-Standard Скачать руководство пользователя

Страница: 4 / 33

ActiveCare - Standard

User Manual

MAN-ActiveCare REV03

ActiveCare Standard USER MANUAL

Page 4 of 33

WARNING

Close supervision by an adult who has read and understands this User

Manual is required when the bed is used around children or others who have not or
cannot read and/or understand this User Manual.

WARNING

The bed mattress must be purchased from Med-Mizer Inc. to meet

entrapment zone dimensional guidelines published by the Food and Drug Administration.

WARNING

Do not spill or spray liquid on the bed.

Excessive liquid on the bed can

result in an electric shock hazard. In the event of a liquid spill or excessive liquid on the
bed, unplug the bed immediately. Remove excess liquid and allow bed to dry thoroughly
before restoring power.

WARNING

Never permit anyone under the bed while the bed is being used. Failure to do

so could result in personal injury.

WARNING

Never operate the bed if a cord or plug is damaged, or it is not working

properly. Contact Qualified Service Personnel for inspection and/or repair. Failure to do so
could result in personal injury.

WARNING

DO NOT sit or lie on hand control. It can cause unintended movement of the

application.

WARNING

Ensure the main power cord is routed where it is not pinched either under or

beside the bed. Failure to do so could result in personal injury or equipment damage.

CAUTION

Ensure the grounding cable of the control box is securely fastened to the frame.

Failure to do so could result in personal injury or equipment damage.

CAUTION

If a handset is used, the cord must be routed and secured properly to ensure

that cord does not become entangled. Failure to do so could result in equipment damage or
personal injury.

CAUTION

Keep all moving parts free of obstruction (i.e. blankets, sheets, pads, tubing,

etc.)

CAUTION

Never remove any labels applied to the bed. Failure to do so could result in

personal injury or equipment damage.

CAUTION

Do not exceed the maximum allowable weight capacity on this bed. The

maximum weight is the sum of the resident/patient, mattress, bedding material, and
accessories.

Содержание ActiveCare-Standard


































Результаты поиска

Содержание ActiveCare-Standard

Отзывы:

Похожие инструкции для ActiveCare-Standard

Бренды по названию

Популярные бренды

Med-Mizer ActiveCare-Standard, Руководство пользователя

Результаты поиска

Содержание ActiveCare-Standard

Отзывы:

Похожие инструкции для ActiveCare-Standard

Бренды по названию

Популярные бренды