Med-Mizer ActiveCare-Standard Скачать руководство пользователя страница 31

Страница: 31 / 33

ActiveCare - Standard

User Manual

MAN-ActiveCare REV03

ActiveCare Standard USER MANUAL

Page 31 of 33

Verify that cables and wires are properly retained and
clear of moving parts

Remove bed from service. Securely retain wires so they
are clear of moving parts. Contact Med-Mizer® customer
service to order replacement missing or damaged wire
fasteners.

Verify the plug connectors for the controls, drive
motors, and motor control box are fully engaged

Fully engage connectors that are not properly engaged.

Verify the side rails/ assist bars latch securely in the
raised position

Remove bed from service. Contact Med-Mizer®
customer service.

Verify all casters securely lock when activated

Remove bed from service. Contact Med-Mizer®
customer service to order replacement non-locking
casters.

Verify that all bed control switches operate correctly.

Contact Med-Mizer® customer service.

Service Parts List

Contact Med-Mizer® customer service at (877) 867-7365 to order parts

PART

DESCRIPTION

6201

LINAK POWER CHORD 11 FOOT W/ GROUND CABLE (912143)

6947

HI/LO BARIATRIC ACTUATOR (40050400012DB16134200)

6948

HI/LOW & HEAD (40040250031DB142322000)

6949

KNEE ACTUATOR (40040055011DB129342000)

6950

PIVOT ACTUATOR (40090400011DB161332000)

6951

LEG ACTUATOR (40040130011DB130012000)

6952

CONTROL BOX (CO61-U047-01)

6955

HB8X348-00 Active Care Handset Full

6958

CONTROL BOX MOUNTING BRACKET (1015W1001-C)

6974

POWER JUNCTION BOX - PJ2+19200S00000

7006

ACTUATOR CABLE HEAD/KNEE MOTOR 750MM (00914681-750-B)

7007

ACTUATOR CABLE PIVOT MOTOR 1575MM (00914681-1575)

7008

ACTUATOR CALE LEG MOTOR 600MM (00914681-600)

7009

ACTUATOR CABLE HI/LOW 3100MM (0965344-A)

7058

COVER, KNEE PIVOT LEFT

7059

COVER, KNEE PIVOT RIGHT

7213

4" DUAL WHEEL TOTAL LOCK CASTER BLACK

7174

CHERRY BOARD

7175

RIFT OAK BOARD

7176

OBSIDIAN BOARD

Содержание ActiveCare-Standard


































Результаты поиска

Содержание ActiveCare-Standard

Отзывы:

Похожие инструкции для ActiveCare-Standard

Бренды по названию

Популярные бренды

Med-Mizer ActiveCare-Standard, Руководство пользователя

Результаты поиска

Содержание ActiveCare-Standard

Отзывы:

Похожие инструкции для ActiveCare-Standard

Бренды по названию

Популярные бренды