MED Associates PHM-104A Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 22

MED Associates PHM-104A Скачать руководство пользователя страница 20

MED ASSOCIATES, INC.

PHM-104A HIGH/LOW SPEED PRECISION PUMP

| PHM-104A DRIVER AND SOFTWARE INSTALLATION

Chapter 4

PHM-104A driver and software installation must be completed before the pump can be controlled via
software.

NOTE: The PHM-104A driver is specific to the computer USB port that the pump is connected to
during driver installation. For this reason, it will be necessary to complete driver installation again if
the PHM-104A is connected to a different USB port at a later time.

Insert the PHM-104A CD into the CD-ROM drive and the screen shown in Figure 4.1 – PHM-104A Main
Screen will appear. Click

Install the PHM-104A High-Low Speed Pump Software

and the screen shown

in Figure 4.2 will appear.

Figure 4.1 – PHM-104A Main Screen

Click

Install

to begin installation. Follow the steps to complete the PHM-104A driver and software

installation. When installation is complete, the screen shown in Figure 4.3 will appear.

Figure 4.2 – Installation Checklist

- 16 -

DOC-187 Rev. 1.6 Copyright © 2019

Med Associates, Inc.

«
...
18
19
20
21
22
»

Содержание PHM-104A























Отзывы:

Нет отзывов