manualshive.com logo in svg

MED Associates PHM-104A, Руководство пользователя, Страница: 19 / 22

Поделиться
Скачать
MED Associates PHM-104A Скачать руководство пользователя страница 19

MED ASSOCIATES, INC. 

PHM-104A HIGH/LOW SPEED PRECISION PUMP 

 

28-V Output Via MED-PC 

This section describes the procedure for using a MED-PC 28-Volt output to turn the pump on and off.  
The pump will operate using the default parameters.   

1.

 

Using the 24 VDC power supply connect the 

24 VOLTS

 connector on the PHM-104A to a standard 

wall outlet. 

2.

 

Turn the PHM-104A on using the green ON/OFF switch. 

3.

 

Set the pump’s default parameters using the pump control application described in  Figure  3.4  - 
PHM-104A Control Software Screen. 

4.

 

Connect the 

MED OPERATE

 port (Figure 2.3) on the pump to any available output on a standard 

MED Connection Panel (e.g. SG-716D), using the included cable. 

NOTE:  Be sure that the USB cable is NOT connected to the pump, as the MED OPERATE port will not 
be recognized if it is. 

5.

 

Set the FLUSH/REMOTE/TEST switch to 

REMOTE

.  The pump will now execute a complete infusion 

using the default parameters each time it receives a 28-Volt output pulse from MED-PC. 

 

 

 

- 15 -

 

DOC-187 Rev. 1.6 Copyright © 2019 

Med Associates, Inc. 

Содержание PHM-104A























Отзывы:

Нет отзывов