800-797-4632 . mecoutdoors.com
11
MEC AUTO-MATE ASSEMBLY MANUAL
Step 16:
Install the right hand reloader support bracket
using the provided 1/4” nut and bolt. Start
with the top bolt as shown here and finger
tighten.
IMPORTANT: If you are converting the
8567N Grabber you will need to contact
MEC Outdoors to purchase the right hand
truss rod #9130P9 and wing thumb screw #
9105.
Step 17:
Complete the installation of the reloader
support bracket by securing the bottom of the
bracket to the reloader. Tighten both bolts
securely using (2) 7/16” wrenches.
NOTE
: Make certain this connection is made
on the back side of the indexer side plate as
shown.
IMPORTANT: Follow instructions for 8567
Grabber right hand truss rod #9130P9
assembly.
Step 15:
Lower charge bar assembly.
From the side/back view of the reloader this is
what the finished assembly should look like.
Congratulations, you are almost ready to go!
15
THIS IS WHAT THE FINISHED
ASSEMBLY SHOULD LOOK LIKE.
CONGRATULATIONS, YOU ARE
ALMOST READY TO GO!
STEP 16
WITH A 7/16” END WRENCH, INSTALL
THE LOADER SUPPORT BRACKET.
USE THE PROVIDED ¼” NUT AND
BOLT. START WITH THE TOP BOLT
AS SHOWN HERE. TIGHTEN
SECURELY.
IMPORTANT: IF YOU ARE
CONVERTING A GRABBER 8567
CALL THE FACTORY AND REQUEST
THE RIGHT HAND TRUSS ROD
#9130P9
STEP 17
WITH A 7/16” END WRENCH,
COMPLETE THE INSTALLATION OF
THE LOADER SUPPORT BRACKET BY
SECURING THE BOTTOM OF
BRACKET TO LOADER. TIGHTEN
SECURELY.
NOTE: MAKE CERTAIN THIS
CONNECTION IS MADE ON THE
BACKSIDE OF THE INDEXER SIDE
PLATE AS SHOWN.
IMPORTANT: FOLLOW
INSTRUCTIONS FOR 8567 GRABBER
RIGHT HAND TRUSS ROD #9130P9
ASSEMBLY.
15
THIS IS WHAT THE FINISHED
ASSEMBLY SHOULD LOOK LIKE.
CONGRATULATIONS, YOU ARE
ALMOST READY TO GO!
STEP 16
WITH A 7/16” END WRENCH, INSTALL
THE LOADER SUPPORT BRACKET.
USE THE PROVIDED ¼” NUT AND
BOLT. START WITH THE TOP BOLT
AS SHOWN HERE. TIGHTEN
SECURELY.
IMPORTANT: IF YOU ARE
CONVERTING A GRABBER 8567
CALL THE FACTORY AND REQUEST
THE RIGHT HAND TRUSS ROD
#9130P9
STEP 17
WITH A 7/16” END WRENCH,
COMPLETE THE INSTALLATION OF
THE LOADER SUPPORT BRACKET BY
SECURING THE BOTTOM OF
BRACKET TO LOADER. TIGHTEN
SECURELY.
NOTE: MAKE CERTAIN THIS
CONNECTION IS MADE ON THE
BACKSIDE OF THE INDEXER SIDE
PLATE AS SHOWN.
IMPORTANT: FOLLOW
INSTRUCTIONS FOR 8567 GRABBER
RIGHT HAND TRUSS ROD #9130P9
ASSEMBLY.
15
THIS IS WHAT THE FINISHED
ASSEMBLY SHOULD LOOK LIKE.
CONGRATULATIONS, YOU ARE
ALMOST READY TO GO!
STEP 16
WITH A 7/16” END WRENCH, INSTALL
THE LOADER SUPPORT BRACKET.
USE THE PROVIDED ¼” NUT AND
BOLT. START WITH THE TOP BOLT
AS SHOWN HERE. TIGHTEN
SECURELY.
IMPORTANT: IF YOU ARE
CONVERTING A GRABBER 8567
CALL THE FACTORY AND REQUEST
THE RIGHT HAND TRUSS ROD
#9130P9
STEP 17
WITH A 7/16” END WRENCH,
COMPLETE THE INSTALLATION OF
THE LOADER SUPPORT BRACKET BY
SECURING THE BOTTOM OF
BRACKET TO LOADER. TIGHTEN
SECURELY.
NOTE: MAKE CERTAIN THIS
CONNECTION IS MADE ON THE
BACKSIDE OF THE INDEXER SIDE
PLATE AS SHOWN.
IMPORTANT: FOLLOW
INSTRUCTIONS FOR 8567 GRABBER
RIGHT HAND TRUSS ROD #9130P9
ASSEMBLY.
Bolt/Nut
►
Bolt/Nut
►
