MD MD-AWD-150 страница 30 Скачать руководство пользователя | Manualshive

Страница: 30 / 49

background image

Mustang Dynamometer

MD-AWD-150

Page 30

For the control system installation you will need the contents of box # 3 (the box you found this
manual in), Monitor, PC, and you will need to install the PowerDyne control box.
NOTE: There is only 30 feet of cable supplied with the dynamometer so double check the
placement of the PowerDyne control box to the placement of your dynamometer.

4.7.1 Control System Installation Procedure

1. Take the “dummy” load cell out by removing the large bolts from the upper and lower

load cell brackets. Attach the load cell on the lower bracket first. Upon completion,
attach the load cell to the upper bracket. Tighten both bolts to 50 ft.-lbs. Torque the
eyelet bolt jam nuts to 200 in.-lbs. DO NOT OVER TIGHTEN! NOTE: Position the load
cell so the wire is on the side opposite the Power Absorbing Unit.

2. Route cabling and air line. Leave enough slack in the cables and the air line so that the

appropriate connections can be made.

3. After routing the air line, push the plastic air line into the quick release air fitting on the

air solenoid until it is snug. Make sure that the air line will not come into contact with
the rolls.

«
...
28
29
30
31
32
...
»

Содержание MD-AWD-150


















































Отзывы:

Нет отзывов

Похожие инструкции для MD-AWD-150

Бренд: Calistair Страницы: 44

Бренд: OMCA Страницы: 72

Бренд: Labnet Страницы: 5

Бренд: Makita Страницы: 8

Бренд: VECTECH Страницы: 5

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Бренд: Dana Design Страницы: 20

Бренд: Hach Страницы: 66

Бренд: Hach Страницы: 14

Бренд: Hach Страницы: 144

QuikChem 8500 2 Series

Бренд: Hach Страницы: 80

Бренд: Hach Страницы: 178

Бренд: Hach Страницы: 32

Бренд: hager Страницы: 4

Бренд: Samson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды