when the burner has not been heated up, and the device should
work on min. power (22 kW). During this time, the pump feeds
the combustion chamber with approximately 1.85 kg/h of oil.
After 30 minutes, we may shift to max. power (30 kW), during
which time the chamber is supplied with approximately 2.55 kg/h
of oil.
► The heater is switched off by pressing Stop button on the
control panel. The pump is switched off (yellow and green di
-
odes on the control panel go off). Fan works until the temper
-
ature in the chamber falls below 35°C (Shutting off). After the
temperature in the chamber has fallen below 35°C, the burner
switches to the Stop mode.
► The heater may switch off automatically if the combustion
chamber is overheated or in case of overflow.
► Overheating signal is generated by the bimetallic thermostat
located close to the fan. Opening of joints signals that the thresh
-
old temperature has been exceeded. Control system turns the
pump off (pump indicator, yellow diode, goes off) and overheat
-
ing is signalled when a red diode on the control panel switches
on. Fan works until the temperature in the chamber falls below
35°C. After the temperature in the chamber has fallen below
35°C, the burner switches to the Stop mode.
► Once the heater is in the Stop mode (and even after switch
-
ing off and subsequently switching on the device) the overheat
-
ing signal is on. This enables the user to find out what caused
the heater to stop.
► In order to reset the overheating signal and regain normal
functioning of the device, one should wait until the burner cools
off completely (ventilation fan switches off) and press the button
on the casing of bimetallic thermostat. Then press Start button,
which will cause the overheating diode to go off. The heater may
be switched on again.
► Overflow signal is generated by a mechanic sensor located
underneath the overflow tank. Opening of joints signals that the
tank is overflow. At the same time the pump is switched off, the
pump indicator goes off, and the red diode signalling overflow
switches on. Fan works until the temperature in the chamber
falls below 35°C. After the temperature in the chamber has
fallen below 35°C, the burner switches to the Stop mode. The
overflow tank is to be emptied, and then Start button should be
pressed, which will cause the red overflow diode to go off. The
heater may be switched on again.
►►
►
9. HOW TO OPERATE THE HEATER
CAUTION!
OIL MUST NOT BE POURED INTO THE BURNER IF
THE CHAMBER OR THE PAN IS STILL HOT!!! AL
-
WAYS WAIT UNTIL THE BURNER HAS COOLED
DOWN. NON-COMPLIANCE WITH THE ABOVE WARN
-
ING MAY CAUSE EXPLOSION OF OIL VAPOURS AND
BURNS!!!
HOW TO OPERATE THE DEVICE
► Once engaged, the heater switches to desired modes de
-
pending on settings chosen by the user and information trans
-
mitted by sensors connected to the control panel.
► If necessary, water may be poured from the tank and re
-
placed with used oil.
► Plug into the power socket (230V/50Hz).
► Pull the upper part of the cover aside and take the burner lid
off, take the cylinder and the ring out (if necessary, clean thor
-
oughly the vaporising pan and its base, the burner, cylinder and
ring). Check if the vaporising pan is cool and clean, and then
pour approximately 250 ml of heating or diesel oil onto it.
► Light oil using a piece of scrunched up paper that needs to
be put on fire and thrown onto the vaporising pan.
► Install ring and cylinder, put the burner lid back on, close the
upper part of burner’s casing.
► Press Start button on the control panel (green diode turns
on).
► After approx. 10-15 minutes, depending on the temperature
in the room, the fuel pump and ventilation fan will start and the
yellow pump diode will turn on at the same time. The heater
starts working on its minimum power 22 kW; 1.85 kg/h
► Each time Stop button is pressed followed by pressing the
Start button during operation will result in switching into the
Heating up mode of the burner.
SHUTTING OFF
► Press Stop on the control panel (yellow diode goes off),
pump stops feeding fuel onto the vaporising pan, and ventilation
fan works only until the burner has cooled off.
THE DEVICE MUST NOT BE UNPLUGGED FOR
AS LONG AS THE VENTILATION FAN IS WORKING,
THIS CAN BE DONE ONLY AFTER THE BURNER HAS
COOLED DOWN. THE BURNER SWITCHES OFF AU
-
TOMATICALLY. PLEASE REMEMBER THAT AFTER
SWITCHING OFF THE DEVICE, THE CAST-IRON PAN
REMAINS HOTTER FOR LONGER (DEPENDING ON
THE TEMPERATURE IN THE ROOM) AND THE HEAT
-
ER CANNOT BE RE-ENGAGED UNTIL IT COOLS
DOWN COMPLETELY.
MAINTENANCE
► The burner requires various maintenance works. Following
producer’s recommendations regarding maintenance will as
-
sure failure-free and safe functioning of the device.
► Vaporising pan and elements of the combustion chamber
(cylinder, ring and lid) should be cleaned daily.
► Check if the oil overflow pipe is unobstructed (FIG1,p3,p13),
and clean if necessary.
► Clean the burner basin located inside the combustion cham
-
ber at least once a week (burner basin is located under the va
-
porising pan).
► Check if air inlets in the lower and upper part of the combus
-
tion chamber are not obstructed.
► Clean the oil feed line once a week, maximum time of opera
-
tion without cleaning the line feeding oil onto the vaporising pan
is approximately 7-14 hours (depending on the type of oil used
for heating).
► Clean the fuel tank and oil pump filters during heating sea
-
son.
► If the heater is not used for a longer period of time, the com
-
bustion chamber and the tank should be cleaned thoroughly,
and then covered with a thin layer of oil in order to prevent cor
-
rosion.
IT IS RECOMMENDED TO HAVE ALL MAINTE
-
NANCE WORKS DONE EACH SEAZON BY AN AU
-
THORISED DEALER.
►►
►
10. FAILURES AND THEIR REMEDIES
In case of a failure of the device, the following list may help
identify its cause and remedy. Generally, it should be easy to fix.
The following are the most common problems. Digits represent
possible causes. The order of digits suggests gradation of prob
-
able cause of the failure.
CAUTION!
UNPLUG THE DEVICE BEFORE STARTING TO FIX
THE PROBLEM.
BG
CZ
DE
FI
FR
GB
PL
RU
SE
SE
SI
SK