background image

McQuay IM 777-1

27

Service and Maintenance

To remove the fan assembly:

1

Remove the side panels and any intermediate supports 
(follow instructions for side panel removal)

2

Once the panels and any intermediate supports are 
removed, disconnect the neoprene bulk head seal that is 
attached to the fan discharge

3

Remove the four discharge angles that hold the neoprene 
canvas in place around the discharge opening

4

Disconnect the fan sled from each of the corner mounts and 
pull the entire assembly out the side of the unit

5

After the fan sled is out, loosen the fan bearings and pull 
out the shaft

6

Disconnect the fan housing from the fan sled, and bearing 
support by removing the attaching bolts

7

Replace the new fan, reconnect the shaft and bearings and 
put the fan assembly in the cabinet.

8

Replace panels and fasteners.

Removing and Replacing the Coil

Removing Single Coils

Note –

Single coils are bolted to the unit on the connection end. 
The connection end is held in place with a clamp. 

See

Figure 39

.

1

Disconnect all piping and remove the brass plugs for the 
vents and drains located in the connections. 

2

Remove all screws and remove the access panel.

3

Remove the screws holding the coil in place

4

Lift and pull the coil out the side.

Installing Single Coils

1

Slide the coil through the opening in the coil section onto 
the bottom coil rests.

2

To prevent any air bypass around the coil, place coils up 
against the coil bulkheads. See Figure 39

.

3

Once the coil is in place, fasten the coil to the section. 

4

Caulk the seams between the coil casings and bulkheads

.

See Figure 39

.

5

If this is an additional coil being installed and not a 
replacement, locate the coil supply and return connections 
dimensionally. Carefully drill holes in the end panels of the 
unit.

6

Remove the brass plugs for the vents and drains on the 
connections.

7

Slip the panel over the connections. 

8

Replace the brass plugs and panel fasteners.

Figure 39: Single coil installation/removal

Removing Stacked Coils

Note –

Top and bottom stacked coils are held together with steel 
plate and screws on one side and drain trough and 
screws on the other side. Remove the plate and trough 
before removing the coils. The coils cannot be removed 
attached together.

1

Disconnect all piping and remove the brass plugs for the 
vents and drains located in the connections. 

2

Remove all screws and remove the access panel.

3

Remove the bolts holding the coil in place and then lift and 
pull out the coil from the side.

4

Remove the steel plate and the drain trough that hold the 
coils together.

5

Remove the bolts on both ends of the top coil holding it in 
place and then lift and slide the coil out.

6

Remove the bolts on both ends of the bottom coil holding it 
in place and then lift and slide the coil out.

Installing Stacked Coils

1

Slide the bottom coil through the opening in the coil section 
onto the bottom coil rests. 

2

Place the coil up against the coil bulkheads to prevent any 
air bypass around the coil. 

3

Once the coil is in place, bolt the coil to the section.

4

Caulk the mounting surface of the steel plate and install the 
plate on the coils.

5

Caulk the mounting surface of the drain trough and install 
the drain trough on the coils.

6

Caulk the seams between the coil casings and blockoffs

.

Coil

Connection end

Coil

Opposite connection  end

Coil 
Bulkhead

Coil 
Rests

Содержание Skyline IM 777-1





































Отзывы:

Похожие инструкции для Skyline IM 777-1