1-3
Model
5AC030CR
5AC040CR
5AC050CR
5AC055CR
Voltage Range **
380 ~ 420V /3Ph /50Hz + N +
!
Recommended Fuse *
A 25
29
33
36
Power Supply Cable Size *
mm
2
10
10
10
10
Number of Conductor
3
3
3
3
Interconnection Cable Size *
mm
2
1.5
1.5
1.5
1.5
!
!
!
!
!
CAUTION
•
Do not allow water to remain in the water pipes if the unit is not operating for a long period.
Water must be drained out if the unit is not running during winter. Failing to do so would cause the pipe to crack.
•
Do not drink the chilled water in the unit.
ELECTRICAL AND WIRING
•
Refer to the wiring diagram provided on the unit when making electrical wiring. See page iii / iv.
ELECTRICAL DATA
Table B : ( R410A - Heatpump )
Model
5AC030CR
5AC040CR
5AC050CR
5AC055CR
Power Supply
V-ph-Hz
400 / 3 /50
400 / 3 /50
400 / 3 /50
400 / 3 /50
Voltage range
V
380 ~ 420
380 ~ 420
380 ~ 420
380 ~ 420
Nominal Power Input (Cooling/Heating)
kW
3.7 / 3.6
4.3 / 4.5
5.1 / 5.1
5.3 / 5.4
Nominal Current Input (Cooling/Heating)
A
5.6 / 5.5
6.8 / 7.0
7.7 / 7.8
8.3 / 8.5
Maximum Continous Current (Comp 1/2)
A
12.5 / 12.5
12.5 / 18.3
15.4 / 19.4
19.4 / 19.4
Full Load Current (Comp 1/2)
A
35.2 / 35.2
35.2 / 67.0
58.0 / 68.0
68.0 / 68.0
Pump Power Input (Cooling/Heating)
W
199 / 214
312 / 322
339 / 347
345 / 353
RECOMMENDED FUSE AND CABLE SIZES
IMPORTANT
:
*
The figures shown in the table are for information purpose only. They should be checked and selected to
comply with the local/national codes of regulations. This is also subjected to the type of installation and
conductors used.
** The appropriate voltage range should be checked with label data on the unit.
!
!
!
!
!
CAUTION
•
All field wiring must be installed in accordance with the national wiring regulation.
•
All the terminals and connections must be tightened. Improper connection and fastenings could cause electric shock,
short circuit and fire.
•
Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing wiring work
according to the wiring diagram.
•
The unit must be GROUNDED to prevent possible hazards due to insulation failure. Do not ground any electrical
equipment to the water piping.
•
All electrical wiring must not touch the refrigerant piping, compressor, pump, fan motor or any moving parts of
the fan motors.
•
Do not operate the chiller with wet hands. It would result in electric shock.
•
Do not use fuse of different amperage than stated. Using wire etc. to replace a fuse could cause equipment damage
or fire.
•
Neutral wire size must be 3 times larger than the incoming live wire size.
Содержание R410A SINGLE COMPRESSOR SERIES
