background image

                                                                                                                                User Manual

 

 

     

 

6

 

 

Schedule

 

 

        Any icon from 

  stands  for  one  time  period, and there are 4 periods  can be set in 

one day.   

 

Under the time setting mode, press 

 

to enter into time setting interface, the time parameter 

of cooling or heating mode can be set. Press 

  then 

switch among 

7 days 

 

5+2 days

 

 

a whole week:

 [ 

MON

TUE

WED

THU→FRI→SAT→SUN→

MON TUE WED THU FRI

SAT SUN

MON  TUE  WED  THU  FRI  SAT  SUN

 

]. 

When  setting  the  parameters,  press  F  to  exit  to  the 

modify interface, then get back to the temperature setting interface. 

       

 

1.  Press 

flashes

 

then  press 

 

or 

  to  change  the  time  (changes  in  15  minutes  at  a 

time); 

 

2.  After  completed  the  time  setting,  Press

  to  switch  to  the  temperature  setting,  setting 

temperature flash and press 

  or 

  to modify the setting temperature. 

 

3. After finished the above steps, press 

  to switch to 2

st

 period of Monday and repeat item 

1  and  2  steps,  then  complete  4  periods  of  Monday  setting.  Press 

  to  save  and  enter 

schedule setting for the following day.   

 

Under  the  time  setting  mode,  when  the  time  is  set  to  -  -

-  -,  the  current  schedule  will  be 

disabled, and it will follow the  previous time setting  until enter into the  next schedule. If 4 

period of a day is - - -

- --, then it will run the last schedule by default. 

The below table is the time parameter setting in different modes: 

(Factory Default)

 

 

 

 

 

 

 

 

 

Notes: Cooling and Auto mode use the same setting schedule.

 

 

 

Hold 

This  mode  comes  after  “

Schedule

”  by  pressing 

F

.  In  this  mode,  device  will  keep  a  constant 

temperature until next change. 

 

“Hold” 

&  “

 

display  and  temperature  value  flashing.  Press 

 

or 

 

can  change 

the value, and press 

F

 to save the setting; 

 

Press 

  can set system state;   

 

Press 

  can set fan mode.

 

 

 

Hold Until (Holiday) 

This  mode comes after  “

Hold

”  by pressing 

F

  again. In this  mode, device will  follow the setting 

temperature and lasting days when users are out for a holiday. And then back to follow 

Schedules

 

after the holiday. 

Periods 

Time 

Parameters 

Heating 

Cooling/ Auto 

06:00 

21.0℃ 

25.5℃ 

08:00 

16.5℃ 

29.5℃ 

18:00 

21.0℃ 

25.5℃ 

22:00 

16.5℃ 

28.0℃ 

Содержание MH6-HP










Отзывы: