background image

Installing Socket Fusion Heater Adapters

The heater body of this assembly is not coated. Coated heater 

adapters are available for all fusion applications.
Heater adapters are installed with Stainless Steel Cap Screws.
Care should be taken to assure that the heater adapters are 

seated on the heater body, and that there is no foreign matter 

trapped between these surfaces.

IMPORTANT:

 Do not over-tighten the bolts.

The surface of the heater adapters are coated with an anti-stick 

coating.

NOTICE:

 Only install heater adapters when the heater is cool.

TX01413-6-17-10

Maintenance

PH

0419

9-6

-11-10

4 - 1

Adjusting Heater Temperature

Turn knob to desired temperature.  Measure the heater surface 

temperature with a pyrometer.  Any variance must be corrected to the 

pyrometer reading.
Loosen setscrew in the knob.  Turn knob to point to the same 

temperature as the pyrometer.  Tighten setscrew in the knob.  
Turn knob to desired temperature.  Allow heater to stabilize at the new 

temperature (5 to 10 minutes) after adjusting.
The thermometer on the heater body indicates internal temperature and 

should be used as a reference only.

TX02009-3-13-02

PH

02

313-

4-

24

-0

2

Heater Indicator Light

The heater has a green indicator light which will flash on and off.  This 

indicates that the controller is operating normally.  If the green indicator 

is not flashing then the controller may not be operating properly.  If this 

occurs, disconnect power and have the heater repaired by an McElroy 

Authorized Service Center.

The heater has a red indicator light on the handle at the bottom of the 

temperature scale.  When the heater is plugged in and preheating the 

red light glows steadily until the set temperature is reached.  The red 

light then goes off and on as the heater maintains temperature.

If the heater is not operating properly, the control will attempt to turn the 

heater off and the red indicator light will flash rapidly.  If this occurs, 

disconnect the power and take it to a McElroy Authorized Service 

Center for repair.

TX04036-4-12-10

PH

02

31

4-

4-

24

-02

PH

02

571-0

9-16

-0

3

Содержание Socket Fusion



















Отзывы: