McCue CartPark Architectural Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 11

McCue CartPark Architectural Скачать руководство пользователя страница 3

CartPark Architectural |

Page 3 of 11

2

Assemble right and left side frames

On a flat surface, set the back right vertical post, front vertical,
lower side rail and upper side rail as shown. Slide upper side
rail so that the notch is facing up and into the back right post
as shown in detail A.

Secure both lower and upper side rail to vertical posts with
14, Taptite ¼-20 x 1.0” screws coated with wax at the front and
back of the vertical posts. Do not over-tighten the screws.
Repeat this step to assemble the left side. Pieces should be
protected from scratches during the installation process.

1

Back Right

Front

Bottom Siderail

Notch Cut

Back Right

Back Left

Stopbar

Opening

Stand sides upright

When both left and right side frames are complete, stand sides
frame upright making sure that the cut out openings for the
stopbar are facing each other on the right and left back vertical
posts. The stopbar openings should be located towards the
back of the unit.

«
1
2
3
4
5
...
»

Содержание CartPark Architectural












Отзывы:

Нет отзывов