background image

Common-1

 

iPod INTEGRATION MODULE

 

INSTALLATION INSTRUCTIONS

 

Vehicle: Mazda2, Mazda3, Mazda5, Mazda6, Mazda RX-8 

Mazda MX-5, Mazda CX-7, Mazda BT-50,   

New Mazda2, New Mazda6 

Parts number

C9F2 V6 572 EU

 

 

Thank you for purchasing a genuine Mazda accessory. 
Before removal and installation, be sure to thoroughly read these instructions. 
Please read the contents of this booklet in order to properly install and use the iPod integration module. 
Your safety depends on it. 
Keep these instructions with your vehicle records for future reference. 

 

Note:

 

z

 

There are several

 

WARNING

 

and

 

CAUTION

 

sections in this booklet concerning 

safety when

 

installing or removing the iPod integration module. Always read and follow 

them in order to prevent injuries,

 

accidents, and possible damage to the vehicle.

 

 

 

WARNING:

   

Indicates a situation in which serious injury or death could result if the 
warning is ignored.

 

 CAUTION:

   

Indicates a situation in which bodily injury or damage to the vehicle could 
result if the caution is ignored.

   

 

z

 

Do not modify the iPod integration module.   

z

 

Do not install the iPod integration module in any way other than described in the following 
instructions. 

z

 

If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent 
errors in installation. 

z

 

If you have any questions about the use of the accessory, ask your Mazda dealer for proper 
advice before using it. 

z

 

Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons 
and property that arise from the failure of the dealer or installer to follow these instructions. 

z

 

To ensure safety and reliability of the work, installation, removal and disposal work by an 
Authorized Mazda Dealership is recommended. 

z

 

Be careful not to lose removed parts, and be sure that they are kept free from scratches, 
grease or other dirt. 

 
 
 

 
 
 
 
 

 

* iPod is a trademark of Apple Computer, Inc., registered in the United States and other countries.

 

 

To the dealer 

Please turn over these instructions to the customer after installation.

 

To the customer 

z

 

Keep these instructions after installation. The instructions may be

 

necessary for installing other 

optional parts or removal of this accessory.

 

z

 

Should the vehicle or this accessory be resold, always leave these instructions with it for the next 
owner.

 

GE

1ED6P11A13300

Содержание C9F2 V6 572 EU

























































Отзывы: