Maytag MER5551BA - 30'' Electric Range Скачать руководство пользователя

Страница: 20 / 55

16026784

WARNING

To avoid risk of electrical shock, personal injury or
death; disconnect power to unit before servicing.

Disassembly Procedures

Ribbon Elements (select models)

1. Remove maintop assembly, see "Maintop Assembly"

procedure.

2. Remove screws securing element support bracket to

maintop.

3. Label and disconnect wire terminals from element

being replaced.

4. Release metal clips securing element to element

support bracket.

5. Replace and reverse procedures to reinstall element.

Coil Element Terminal (select models)

1. Remove maintop assembly, see "Maintop Assembly"

procedure.

2. Remove screw securing element support bracket to

maintop.

3. Label and disconnect wire terminals from element

being replaced.

Oven Door Latch Assembly (select models)

1. Remove maintop assembly, see "Maintop Assembly"

procedure.

2. Remove screws securing latch assembly to the front

of the oven cavity outer shell.

3. Label and disconnect wire terminals from latch

assembly.

4. Reverse procedures to reinstall door latch assembly.

Oven Door Removal

WARNING

To avoid risk of personal injury or property damage,
do not lift oven door by the handle.

1. Open oven door slightly and grasp door on both

sides.

2. Lift up and off the hinge receivers.
3. Reverse procedures to reinstall oven door.

Oven Door Hinge

1. Turn off power to unit.
2. Remove oven door, see "Oven Door Removal"

procedure.

3. Remove maintop assembly, see "Maintop Assembly"

procedure.

4. Remove side panel, see "Side Panel Removal"

procedures.

Convenience Outlet/Circuit Breaker
(Canadian Models)

1. Remove control panel, see "Control Panel" procedure

for removal.

2. Label and disconnect wire terminals from

convenience outlet and/or circuit breaker.

3. Remove screws securing outlet and/or circuit breaker

to backguard and push outward to release.

4 . Reverse procedure to reinstall convenience outlet

and/or circuit breaker.

Oven Sensor

1. Disconnect power before servicing.
2. Open oven door and remove screws securing sensor

to oven cavity.

NOTE: Gently

pull wiring through cavity wall.

3. Disconnect oven sensor at the connector terminal

and remove.

4. Reverse procedure to reinstall sensor.

NOTE:

Verify connection is pushed through the

insulation.

Oven Sensor

Bake Element

1. Turn power off.
2. Remove screws securing bake element to rear of

oven wall.

3. Pull element forward to allow disconnection of

terminals on each element leg.

4. Reverse procedures to reinstall bake element.

Broil Element

1. Turn power off.
2. Remove screws securing broil element to top and

rear of oven cavity.

3. Pull broil element forward to allow disconnection of

terminals on each element leg.

4. Reverse procedures to reinstall broil element.

Содержание MER5551BA - 30'' Electric Range
























































Результаты поиска

Содержание MER5551BA - 30'' Electric Range

Отзывы:

Похожие инструкции для MER5551BA - 30'' Electric Range

Бренды по названию

Популярные бренды

Maytag MER5551BA - 30'' Electric Range, Руководство по обслуживанию

Результаты поиска

Содержание MER5551BA - 30'' Electric Range

Отзывы:

Похожие инструкции для MER5551BA - 30'' Electric Range

Бренды по названию

Популярные бренды