background image

3

IMPORTANT INFORMATION

 

 

Special Warning for Installation of Furnace or Air Handling Units in
Enclosed Areas such as Garages, Utility Rooms or Parking Areas

Carbon monoxide producing devices (such as an automobile, space
heater, gas water heater, etc.) should not be operated in enclosed areas
such as unventilated garages, utility rooms or parking areas because of
the danger of carbon monoxide (CO) poisoning resulting from the exhaust
emissions.  If a furnace or air handler is installed in an enclosed area such
as a garage, utility room or parking area and a carbon monoxide producing
device is operated therein, there must be adequate, direct outside
ventilation.

This ventilation is necessary to avoid the danger of CO poisoning which
can occur if a carbon monoxide producing device continues to operate in
the enclosed area.  Carbon monoxide emissions can be (re)circulated
throughout the structure if the furnace or air handler is operating in any
mode.

CO can cause serious illness including permanent brain damage or death.

To locate an authorized servicer, please consult your telephone book or the dealer from whom you purchased this
product.  For further assistance, please contact:

CONSUMER INFORMATION LINE

 GOODMAN

®

 BRAND PRODUCTS

TOLL FREE

1-877-254-4729 (U.S. only)

email us at:

[email protected]

fax us at: (731) 856-1821

(Not a technical assistance line for dealers.)

CONSUMER INFORMATION LINE

AMANA

® 

BRAND PRODUCTS

TOLL FREE

1-877-254-4729 (U.S. only)

email us at: [email protected]

fax us at: (731) 856-1821

(Not a technical assistance line for dealers.)

Outside the U.S., call 1-713-861-2500.

(Not a technical assistance line for dealers.) Your telephone company will bill you for the call.

Содержание Amana ADSS8



























































Отзывы: