background image

16

risque  de  déclencher  un  incendie  ou  une  explosion

   because  some  gas  is  heavier  than  air  and  will

DU GAZ

ARRIVEE

INLET

GAS

   position.

   gaz.  Renifler  tout  autour  de  l'appareil,  y  compris prés  du

"OFF/ ARRET"

"ON/MARCHE”

        ARRÊTEZ
.

IN  "ON"  POS

LEVER  SHOWN

MANUAL  GAS

"ON/MARCHE"

MANUEL, EN POS

ROBINET A GAZ

   plancher,  pour  déceler  une  odeur  de  gaz.  Si  c ' est  le  cas,

  STOP.

   faut  procéder  à  des  operations  d'entretien.

 DE  GAZ  DE  L'APPAREIL

POUR  COUPER  L'ADMISSION

ARRÊTEZ.

       Ne  pas  tenter  d'allumer  d'appareils.

   S'il  n'y  a  pas  d'odeur  de  gaz,  passer  à  l'etàpe  suivante.

   sur  la  portion  superieure  de  cette  etiquette.

                         Passer  à  l'etape  B  des  instructions  de  securite

   position.
6. Attendre  cinq  (5)  minutes  pour  laisser  echapper  tout  le

  STOP.            "B"

   gas, go  to  next  step.

   on  this  label  if  you  don't  smell

   in  the  safety  information  above

   then  smell  gas,                Follow

   smell  for  gas,  including  near  the  floor.  If  you

6. Wait  five  (5)  minute s  to  clear  out  any  gas. Then

10. Set thermostat to desired setting.

        Immediately  call  your  gas  supplier  from  a  neighbor's

                                      to  light  the  burner  by  hand.

    qualifié  ou  le  fournisseur  de  gaz.

    de  gaz  de  l'appareil  et  appeler  un  technicien

    instructions  intitulées  Comment  couper  l'admission

                                          loss  of  life.

                             explosion  may  result  causing  property

exactly, a  fire  or

0140F00681  REV  A

   Ne  pas  forcer.

"OFF/ ARRET”

A.

   d'allumer  le  brûleur  manuellement.

   automatiquemen t  le  brûleur.  Ne  pas  tenter

   muni  d'un dispositif  d'allumage  qui  allume

    Cet  appareil  ne  comporte  pas  de  veilleuse.  Il est

        "ON".

  "OFF”

    service  technician  or  gas  company.

    Off  Gas  To Appliance"  and  call  your

    follow  the  instructions  “To Turn

11. If  the  appliance  will  not  operate,

   power  to  the  appliance.

9.  Turn  on  all  electric

8. Replace  access  panel.

TO TURN OFF GAS TO APPLIANCE

OPERATING  INSTRUCTIONS

READ  BEFORE  OPERATING

FOR  YOUR  SAFETY

  "OFF”

   WHAT  TO  DO  IF  YOU  SMELL  GAS

    BEFORE OPERATING

WARNING:

damage, personal  injury  or

                      If  you  do  not  follow  these  instructions

4. Replace  control  access  panel.

   Do  not  force.

3. Push  the  gas  control  l ever  to                 Position.

   if  service  is  to  be  performed.

2.  Turn  off  all  electric  power  to  the  appliance

1. Set  the  thermostat  to  lowest  setting.

   to

7. Push  gas  control  lever

   Do  not  force.

5.  Push  the  gas  control  lever  to                  Position.

   Do  not  try  to  light  the  burner  by  hand.

   device  which  automatically  lights  the  burner.

4. This  appliance  is  equipped  with  an  ignition

3. Turn  off  all  electric  power  to  the  appliance.

2. Set  the  thermostat  to  lowest  setting.

   this  label.

1.                Read  the  safety  information  above  on

   system  and  any  gas  control  which  has  been  underwater.

   the  appliance  and  to  replace  any  part  of  the  control

   Immediately  call  a  qualified  service  technician  to  inspect

D. Do  not  use  this  appliance  if  any  part  has  been  underwater.

   or  explosion.

   technician.  Force  or  attempted  repair  may  result  in  a  fire

   hand,  don't  try  to  repair  it, call  a  qualified  service

   Never  use  tools.  If  the  lever  will  not  push  in  or  turn  by

C. Use  only  your  hand  to  push  in  or  turn  the  gas  control  lever.

        call  the  fire  department.

        If  you  cannot  reach  your  gas  supplier,

        phone.  Follow  the  gas  supplier's  instructions.

        do  not  use  any  phone  in  your  building.

        Do  not  touch  any  electric  switch;

        Do  not  try  to  light  any  appliance.

   settle  on  the  floor.

   area  for  gas.  Be  sure  to  smell  next  to  the  floor

B.                                          smell  all  around  the  appliance

   the  burner.   Do  not  try

   with  a n  ignition  device  which  automatically  lights

A. This  appliance  does  not  have  a  pilot.  It  is  equipped

11. Si  l'appareil  ne  se  met  pas  en  marche, suivre  les

10. Régler  le  thermostat  à  la  température  désirée.

9. Mettre  l'appareil  sous  tension.

8. Remettre  en  place  le  panneau  d'accés.

MISE EN  MARCHE

EN  MARCHE LIRE

LIRE  AVANT  DE  METTRE

   QUE FAIRE  S'IL  Y  A  UNE  ODEUR  DE  GAZ

B. AVANT  DE  LE  FAIRE  FONCTIONNER,

AVERTISSEMENT:

corporelles  ou  la  perte  de  vies  humaines.

entraînant  des  dommages  matériels,  des  lesions

la  lettre  les  instructions  dans  le  presént  manuel 

Quiconque  ne  respecte  pas  à

4. Remettre  en  place  le  panneau  d'accés.

   position.

3. Pousse  le  levier  du  contrôle  du  gaz  à

2. Couper  l'alimentation  électrique  de  l'appareil  s'il

1. Régler  le  thermostat  à  la  température  la  plus  bassé.

7. Pousse  l e  levier  du  contrôle  du  gaz  à

5. Pousse  le  levier  du  contrÔle  du  gaz  a

   allumer  le  brûleur  manuellement.

   d'allumage  automatique,  ne  pas  essayer  à

4. Cet  appareil  menager  etant  dote  d'un  systeme

3. Couper  l'alimentation  électrique  de  l'appareil.

2. Régler  le  thermostat  à  la  température  la  plus  basse.

   section  supérieure  de  cette  étiquette.

1.                            Lisez  les  instructions  de  sécurité  dans  la

   plongées  dans  l'eau.»

   systéme  de  contrôle  et  toute  commande  qui  ont  été

   par  un  technicien  qualifié  et  remplacer  toutr  partie  du

   l'eau,  même  partiellement.  Faire  inspecter  l'appareil

D. Ne  pas  se  servir  de  cet  appareil  s'il  a  été  plongé  dans

   provoquer  un e explosion  ou  un  incendie.»

   tente  de  forcer  la  manette  ou  de  la  réparer  peut

   réparer;  appelez  un  technicien  qualifié.   Quiconque

   Si  la  manette  reste  coincée,  ne  tenter  pas  de  la

   qu'à  la  main.   Ne  jamais  emploer  d'outil  à  cette  fin. 

C. Ne  pousser  ou  tourner  la  manette  d'admission  du  gaz

        appelez  le  service  des  incendies.»

        Si vous  ne  pouvez  rejoindre  le  fournisseur  de  gaz,

        un  voisin.  Suivez  les  instructions  du  fournisseur  de  gaz

        Appelez  immédiatement  votre  fournisseur  de  gaz  depuis

        des  téléphone s  dans  le  bâtiment.

        Ne  toucher  à  aucun  interrupteur;  ne  pas  vous  servir

    peuvent  s'accumuler  au  niveau  du  sol.

    certains  gaz  son t  plus  lourds  que  l'air et

    une  odeur  de  gaz.  Renifler  prés  du  plancher,  car

    renifler  tout  autour  de l'appariel  pour  decéler

OPERATING INSTRUCTIONS

Содержание Amana ADSS8



























































Отзывы: