MAYSER 1005264 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 43

MAYSER 1005264 Скачать руководство пользователя страница 33

281114 v1.3

Operating Instructions USi

Page 33/43

Polymer Electric

Maintenance and cleaning

Maintenance and cleaning

Maintenance

Cleaning

The USi is maintenance-free.

Ä

Repeat the functional test annually.

For harsh environmental conditions or very high detection frequency, the interval for
the functional test is reduced accordingly.

Ä

Clean the outside of the enclosure with conventional cleaning products.

Ä

Allow the enclosure to dry before recommissioning.

Danger of injury due to electrocution!

Ä

Disconnect the USi as well as all devices and live parts in the immediate
environment from the power supply and protect them against being switched
on again (see relevant Operating Instructions).

Ä

Check whether all devices and parts are disconnected from the power supply.

WARNING

Failure due to water penetration

Cleaning with a high-pressure cleaner my result in penetration of water in the
Evaluation Unit (IP65) and failure of the electronic system.

Ä

Never clean the Evaluation Unit with a high-pressure cleaner.

CAUTION

«
...
31
32
33
34
35
...
»

Содержание 1005264












































Отзывы:

Нет отзывов