MAYSER 1005264 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 43

MAYSER 1005264 Скачать руководство пользователя страница 17

281114 v1.3

Operating Instructions USi

Page 17/43

Polymer Electric

Installation

Installation

The installation includes three individual installation steps:
1. Mounting the sensor (ultrasonic transducer)
2. Mounting the Evaluation Unit
3. Wiring the unit cable

Mounting the Sensor (Ultrasonic Transducer)

The sensors can be mounted in any position.
If the sensors are supposed to be mounted in quiet workplaces or in areas where
there are hearing-sensitive animals, the interfering soni

fi

cation must be considered.

Ultrasound is not audible for human beings. The “hard” transmission burst, however,
is perceived as a clearly audible crackle. At a measurement frequency of 20

Hz

(typical), 20 crackles per second are audible. This can be stressful when continu-
ous. Here, it is recommended to not align the sensor directly to the ears, but at an
angle of at least 20°. The same applies for indirect soni

fi

cation re

fl

ected from hard

re

fl

ectors like e.g. walls.

Alternatively, the transmission intensity can be altered via the parameter assign-
ment software (optional).

1. Place one O-Ring in each of the grooves N1 and N2 of the sensor. To do so,

select the corresponding O-rings for the speci

fi

ed mounting

fi

xture (see

below).

Standard mounting

fi

xture

– clamping version –

Optimised mounting

fi

xture

– integrated version –

Tolerances: ISO 2768-1 c

Tolerances: ISO 2768-1 m

with O-rings 18.0

×

2.5 mm

Part number 7502819 (optional)

with O-rings 17.5

×

2.0 mm

Part number 7502820 (optional)

2. Mount the sensor (ultrasonic transducer) in any position in the mounting

brackets.

Sensor:

Dimensions

«
...
15
16
17
18
19
...
»

Содержание 1005264












































Отзывы:

Нет отзывов