Maxwell MW-2313 VT, Инструкция по эксплуатации

Страница: 8 / 20

ENGLISH
8
•
Do not allow children to touch the unit body,
the power cord or the power plug during
operation of the unit.
•
Do not leave children unattended to prevent
using the unit as a toy.
•
Close supervision is necessary when chil-
dren or disabled persons are near the oper-
ating unit.
•
This unit is not intended for usage by chil-
dren. Place the unit out of reach of children
during the operation and cooling down.
•
The unit is not intended for usage by physi-
cally or mentally disabled persons (includ-
ing children) or by persons lacking experi-
ence or knowledge if they are not under
supervision of a person who is responsible
for their safety or if they are not instructed
by this person on the usage of the unit.
•
Children can use the unit ONLY under super-
vision of the person, who is responsible for
their safety, and if they are given all the
necessary and understandable instructions
on safety measures and information about
danger, that can be caused by improper
usage of the unit.
•
To avoid damages, transport the unit in the
original package only.
•
Do not attempt to repair the unit. Do not
disassemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and apply to any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.maxwell-products.ru.
•
Keep the unit in a dry cool place out of reach
of children and disabled persons.
•
Do not use the unit outdoors.
•
For environment protection do not discard
the unit with usual household waste after its
service life expiration; apply to a specialized
center for further recycling.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
USING THE HOT AIR BRUSH
After unit transportation or storage at low
temperature keep it for at least three hours
at room temperature before switching on.
•
Unpack the hot air brush and remove any
stickers that can prevent unit operation.
•
Unwind the power cord completely.
•
Install one of the attachments (1) or (7). To
do this insert the attachment into the hot air
brush body (4) and turn it clockwise. If the
attachment is set properly, you will hear the
release button (2) click.
•
Before switching the unit on, make sure that
your home mains voltage corresponds to
the unit operating voltage.
•
Make sure that the operation mode switch
(3) is set to the position “
0 ”.
•
Insert the power plug into the mains socket.
•
Set the required settings of the air flow
using the switch (3):
«
0 » – the hot air brush is switched off;
« 1 » – low speed and low temperature;
« 2 » – high speed and high temperature.
« » – «cool» air supply
Note: During the first operation some foreign
smell and a small amount of smoke from the
heating element is possible, it is normal.
•
After the hot air brush operation is finished,
switch it off by setting the switch (3) to the
«
0 » position and unplug it.
•
Wait till the hot air brush cools down.
•
To remove the attachment, press and hold
the attachment release button (2) and turn
the attachment counterclockwise.
Overheating protection
Overheating protection switches the hot air
brush off if the outgoing air is too hot. If the
hot air brush is switched off during operation,
set the switch (3) to the «
0 » position, unplug
the unit and make sure that the inlets and
outlets are unblocked. Let the unit cool down
for 5-10 minutes and switch it on again. Do not
block the air inlets during unit operation and
avoid getting of hair into its air inlet.
CLEANING AND CARE
The нot air brush is intended for household
use only.
•
Set the switch (3) to the « 0 » position, dis-
connect the hot air brush from the mains
and let it cool down.
IM MW-2313_new.indd 8 23.06.2017 9:28:38