manualshive.com logo in svg

Maxtor Atlas SCSI Drive 15K II, Руководство по эксплуатации продукта

Поделиться
Скачать
Maxtor Atlas SCSI Drive 15K II Скачать руководство пользователя страница 196

 SCSI Description

5-130

Maxtor Atlas 15K

5.34

RESERVE (6) Command (16h)

The RESERVE and the RELEASE commands are used for contention resolution in 
multiple-initiator systems. The RESERVE command is used to reserve a logical unit. 
The data format and the field descriptions are described in Table 5-181 and Table 5-
182 respectively.

Table 5-181   

RESERVE (6) Command Descriptor Block-Data Format

Table 5-182   

RESERVE (6) Command-Field Descriptions

Note:

The drive returns RESERVATION CONFLICT status if the unit is already 
reserved for another initiator. Once the reservation is honored, any command 
from another initiator (except INQUIRY or REQUEST SENSE) is rejected 
with RESERVATION CONFLICT status.

Bit

Byte

7

6

5

4

3

2

1

0

0

Operation Code (16h)

1

Reserved

3rdPty

Third Party Device ID

Extent

2

Reservation Identification

3 - 4

Extent List Length

5

Control

Field

Description

3rd Pty

When set to 1, it indicates that the Third Party Device ID field is valid.

Third 

Party 

Device ID

Required and used only when the 3rdPty bit is set, in which case this field specifies the SCSI ID (0 
through 7 only) of the initiator to be granted the reservation of the logical unit. The drive preserves the 
reservation until one of the following occurs:

• It is superseded by another valid RESERVE command from the initiator.
• It is released by the same initiator
• It is released by a TARGET RESET message from any initiator.
• It is released by a hard reset condition.

The drive ignores any attempt to release the reservation made by any other initiator. For example, if 
ID7 sends ID2 a Third Party reservation on behalf of ID6 (the target at ID2 gets reserved for the initiator 
ID6), then only ID7 can release the target at ID2 (using a Third Party release). ID6 cannot release the 
reservation even though the reservation was made on its behalf.

Extent

The drive supports reservations only on entire logical units. The value must be 0.

Reserva-

tion Identi-

fication

Any value in this field is ignored by the drive.

Extent List 

Length

Any value in this field is ignored by the drive.

Содержание Atlas SCSI Drive 15K II





































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды