Maxtor Atlas SCSI Drive 15K II Скачать руководство пользователя страница 125

Страница: 125 / 260

SCSI Description

Maxtor Atlas 15K

5-59

5.14.12.3

Negotiated Settings Subpage (Sub Page 3 of Mode Page 19)

The negotiated settings subpage, shown in Table 5-79, is used to report the negotiated
settings of a target for the current I_T nexus.

Table 5-79

Negotiated Settings Subpage (03h)

The Transfer Period Factor field indicates the negotiated transfer period factor for the
current I_T nexus.

The Req/Ack Offset field indicates the negotiated REQ/ACK offset for the current
I_T nexus.

The Transfer Width Exponent field indicates the negotiated transfer width exponent
for the current I_T nexus.

The Protocol Options Bits field contain the negotiated protocol options for the current
I_T nexus.

The TRANSCEIVER MODE field specifies the current bus mode of the target as
defined in Table 5-80.

The SENT PCOMP_EN bit contains the value of the PCOMP_EN bit sent by the
target for the current I_T nexus.

The RECEIVED PCOMP_EN bit contains the value of the PCOMP_EN bit received
by the target for the current I_T nexus.

Table 5-80

Transceiver Mode

Bit

Byte

Transfer Period Factor

Reserved

Req/Ack Offset

Transfer Width Exponent

Reserved

Protocol Option Bits

Reserved

Transceiver

Mode

SENT_

PCOMP_EN

RECEIVED

PCOMP_EN

Reserved

Vendor Specific

Code

Transceiver Mode

00b

Unknown (device not capable of reporting bus mode)

01b

Single-ended

10b

Low-Voltage Differential

11b High-Voltage

Differential

Содержание Atlas SCSI Drive 15K II





































































































































































































































































Результаты поиска

Содержание Atlas SCSI Drive 15K II

Отзывы:

Бренды по названию

Популярные бренды

Maxtor Atlas SCSI Drive 15K II, Руководство по эксплуатации продукта

Результаты поиска

Содержание Atlas SCSI Drive 15K II

Отзывы:

Бренды по названию

Популярные бренды