background image

3

1.3 PC4164-RS Specifications

One PC4164-RS receiver may be installed per PC4010/4020 system

Nominal current draw of 120mA

Frequency: 922 to 926 MHz, Spread Spectrum

Receives signals from up to 56 wireless zones on a PC4010 v3.0 and later, and
up to 64 wireless zones on a PC4020 v3.0 and later

Antenna - orthogonal design for enhanced performance

Programmable supervisory window, 01:00 to 23:59

Location

- can be wired up to 750 ft. / 230 m from the main panel with 22 gauge wire
- connects to Combus
- for longer wire runs, thicker gauge wire must be used.

1.4 Wireless Devices

Please refer to the Installation Instruction sheets of the following devices for more
information.

The PC4164-RS v2.0 can receive signals from the following devices:

WLS904 Motion Detector

WLS906 Smoke Detector

WLS907 Universal Transmitter

WLS908 Panic Pendant

WLS909 Wireless Key (up to 16)

WLS910 Handheld Keypad (up to 4)

Batteries

The wireless devices are designed to use Eveready Alkaline Energizer batteries
only. The WLS908 Panic Pendant is a sealed unit and the batteries cannot be replaced.

NOTE

: Do not use other brands of batteries. Using any other brand voids any approvals

and may affect the system operation.

I   N   T   R   O   D   U   C   T   I   O   N

Содержание PC4164-RS

































Отзывы: