Maxcess MAGPOWR Spyder-Plus, Инструкция по эксплуатации

Страница: 57 / 60

12.0 COMMUNICATION (OPTIONAL)
www.maxcessintl.com MAGPOWR Spyder-Plus MI 850A320 1 M Page 57 of 60
Starting
Modbus
Register
Parameter Name Parameter
Format
Parameter
Type
Used with
Control
Types
Read /
Write
Range
0x99 Actual Output FLOAT None LC, DT, DS,
OPT
Read
Only
{ 0.0 - 100.0 } %
0x9B Actual Diameter FLOAT None LC, OPT Read
Only
{ 0.0 - 999.0 } in.
0x9D Position Setpoint FLOAT None DT, DS Read
Only
{ 0.0 - 100.0 } %
0x9F Actual Position FLOAT None DT, DS Read
Only
{ 0.0 - 100.0 } %
0xA1 Device Name STRING Data LC, DT, DS,
OPT
Read /
Write
31 Characters Maximum
0xB1 Program Version UINT32 None LC, DT, DS,
OPT
Read
Only
920Axxx.yyy
xxx,yyy={0 - 999}
xxx = High Word
yyy = Low Word
0xB3 Modbus Address UINT16 Data LC, DT, DS,
OPT
Read /
Write
{ 0 - 255 }
0xB4 Modbus Byte Order BYTE Data LC, DT, DS,
OPT
Read /
Write
0 = MSB First
1 = LSB First
0xB5 Modbus Word Order BYTE Data LC, DT, DS,
OPT
Read /
Write
0 = MSB First
1 = LSB First
0xB6 Actual Manual Level FLOAT None LC, OPT Read
Only
{ 0.0
– 100.0 } %
0xB8 Enable Load Cell Reading (Dancer) BYTE Data DT, DS Read /
Write
0 = Load Cells Not Enabled
1 = Load Cells Enabled
0xB9 Remote Dancer Setpoint FLOAT Data DT, DS Read /
Write
No Integrator, mode: P or
PD, range = { 0.0
– 5.0 }
With Integrator, mode PI or
PID, range = { 0.0
– 1.0 }.
Multiply this value by 100 to
get percent.
0xBB Setpoint Tension Percent FLOAT Data OPT Read/
Write
{ 0.0
– 100.0 } %
0xBD System Type (Open Loop Tension ) BYTE Data OPT Read/
Write
0 = Unwind
1 = Rewind
0xBE Core Offset FLOAT Data OPT Read/
Write
{ -20.0
– 100.0 } %
0xC0 Actaul Tension Setpoint Percent FLOAT None OPT Read
Only
{ 0.0
– 100.0 } %
0xC2 Actual Tension Percent FLOAT None OPT Read
Only
{ 0.0
– 100.0 } %
0xC4 Initial Screen (Open Loop Tension) BYTE Data OPT Read/
Write
0 = Operator Menu
1 = Tension
2 = Output Level
3 = Diameter
0xC5 Hold Level Multiplier FLOAT Data DT Read/
Write
[0.0-99.0}
12.8 MODBUS MASTER PROGRAM
There is a Modbus master program available to test communications with the Spyder that runs on a PC with
Windows. This program was written as an engineering debugging tool for Modbus software development and is
provided as is. Go to
www.maxcessintl.com . Type the keywords
“spyder modbus” in the Search field and press
the Enter key. When the results are displayed, select Software in the filter list on the left
–
do not click Search a
second time . When results are displayed, click on Spyder Modbus TCP Master Software, which links to a zip file.
Save the zip file to a directory on your computer. Unzip this file and run the SMM.exe file. Use the Configure
screen to set up IP address of the Spyder, update rate and Spyder Program Number. The Spyder program number
is displayed on the Spyder for a few seconds after applying power.