Maxcess MAGPOWR DTR-65 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 45

background image

3–4

INSTALLATION

www.maxcessintl.com

MAGPOWR DTR-65

MI 850A349 1 D

Electrical
installation

WARNING – Death or injury from shock may result from
wiring live power to the DTR-65.

Be sure the power is turned off and locked out before wiring
the DTR-65.

All wiring must comply with the essential requirements of
the appropriate standard(s) and is the responsibility of the
installer.

For fixed/permanent installation of the DTR-65, a suitable
switch or circuit-breaker must be installed as a
disconnecting device and this switch/circuit-breaker needs
to be labelled appropriately.

Wiring to the digital load cell amplifier must be insulated
copper wire with a temperature rating of at least 80

⁰

C. The

wire size must be at least 0.34 mm

2

(22 AWG). Use twisted

pair cable for the power. Use shielded cable for the load cell
and analog output wiring.

The DTR-65 can be powered by either 100-240 VAC 50-60
Hz or by 24 VDC. Only connect to one power source.

«
...
12
13
14
15
16
...
»

Содержание MAGPOWR DTR-65














































Отзывы:

Нет отзывов

Похожие инструкции для MAGPOWR DTR-65

Бренд: Randall Страницы: 9

Бренд: VAC Страницы: 10

Бренд: NAD Страницы: 146

Бренд: NAD Страницы: 14

Бренд: Yamaha Страницы: 101

ProX 840.4 COMP

Бренд: µ-Dimension Страницы: 12

Бренд: Meicheng Страницы: 23

Бренд: Glensound Страницы: 15

Бренд: Xtant Страницы: 2

Бренд: Warmenfat Страницы: 12

BDA-PS9-37/37-90-C

Бренд: G-Wave Страницы: 18

Subwoofer Gadget

Бренд: Natural Bass Technology Страницы: 2

Бренд: Kramer Страницы: 13

Бренд: JET CITY AMPLIFICATION Страницы: 18

Bassman Bassman 100

Бренд: Fender Страницы: 16

Бренд: Harman Kardon Страницы: 12

Stereo 60 MK III M

Бренд: icon Audio Страницы: 9

Бренд: Chord Electronics Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды