Maxcess MAGPOWR DTR-65 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 45

background image

2–5

SAFETY INSTRUCTIONS

www.maxcessintl.com

MAGPOWR DTR-65

MI 850A349 1 D

Basic safety
information

continued

Operation

None, as tasks from the operator are generally not required.

Maintenance and repair

WARNING – Death or injury can result from unexpected
movement of the machine into which the DTR-65 is
installed.
Protect against unexpected movement by removing electrical
power from the digital load cell amplifier and the machine
into which the digital load cell amplifier is installed.

WARNING – Danger of injury from crushing.
Maintenance and repair tasks on the digital load cell
amplifier must be performed only when the machine into
which the DTR-65 has been installed has been stopped and
has been secured from being turned on again.

WARNING – Death or injury from shock may result from
wiring live power to the DTR-65.
Be sure the power is turned off and locked out before wiring
the DTR-65.

Decommissioning

The digital load cell amplifier must be disposed of in accordance with all
the applicable national, state and local regulations.

«
...
8
9
10
11
12
...
»

Содержание MAGPOWR DTR-65














































Отзывы:

Нет отзывов

Похожие инструкции для MAGPOWR DTR-65

Бренд: Ultrasound Страницы: 6

Custom Vibrolux Reverb

Бренд: Fender Страницы: 2

FTDX1200 Series

Бренд: Yaesu Страницы: 20

Бренд: Hagerman Страницы: 7

Бренд: Precision Power Страницы: 12

Бренд: Harley Benton Страницы: 2

Бренд: Zaxcom Страницы: 9

Бренд: Bazooka Страницы: 6

Бренд: Nakamichi Страницы: 16

Amplifier 801-40

Бренд: Raymer Страницы: 4

Бренд: Kramer Страницы: 13

Бренд: QUAD Страницы: 16

Бренд: Phaedrus Audio Страницы: 24

Бренд: thomann Страницы: 36

Бренд: Cyfre Страницы: 2

Бренд: L.R. Baggs Страницы: 8

Бренд: Laney Страницы: 12

Бренд: HAMTRONICS Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды