manualshive.com logo in svg

Max PASJ30(CE), Руководство по эксплуатации и техническому обслуживанию, Страница: 28 / 28

Поделиться
Скачать
Max PASJ30(CE) Скачать руководство пользователя страница 28

28

9. SIMPLIFIED OPERATION CHART

Turn on the power switch.

Depress the switch lever.

Pull/release the trigger while depressing the switch lever.

Do not operate the trigger for five minutes.

Do not operate the trigger for 60 minutes.

Start the work again

Turn off the power 
switch once.

Start the work again

The buzzer makes a "pip" sound.
If you keep depressing (holding 
down) the switch lever, the buzzer 
makes a "peep" sound and the 
blades open.

* If the trigger lock lever has been 

applied with the trigger pulled, re-
lease the lock to open blades.

The buzzer makes a "pip" sound. 
The shears do not operate. (They 
are in the standby mode.)

∗

LED indicates when the battery is 
fully charged.

Shears LED

The green LED 
starts slowly blink-
ing.

Control box LED

The green LED 
lights up.

Shears LED

The Green LED 
stops blinking and 
stays light.

Control box LED

The blades move according to the 
operation of the trigger.
If the trigger is pulled, the blades 
close. If the trigger is released, the 
blades open.

Shears LED

The green LED 
lights up.

Control box LED

The green LED 
lights up.

The buzzer makes a "peep" sound. 
Then, the blades do not move even 
if the trigger is pulled.
(The machine is returned to the 
standby mode.)

Shears LED

The green LED 
starts slowly blink-
ing.

Control box LED

The green LED 
lights up.

The buzzer makes a "peep" sound. 
Then, the blades do not move even 
if the trigger is pulled. (The power is 
turned off.)

Shears LED

The green LED 
stops blinking slow-
ly and turns OFF.

Control box LED

OFF

The green LED 
lights up.

PASJ30.book  28 ページ  ２０１１年１２月９日　金曜日　午後２時１１分

Содержание PASJ30(CE)





























Отзывы:

Нет отзывов