Max PASJ30(CE) Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 28

Max PASJ30(CE) Скачать руководство пользователя страница 22

22

3

When the buzzer sounds from the control
box, turn off the power.

4

Operate the switch as explained in "4.
Switch operation" on page 21. After that,
the opening angle of the blades cannot
be switched over.

∗

If you need to switching the opening angle
of blades, perform steps

1

to

4

again.

6. How to store the shears in the hol-

ster

(Fig. AL) Turn off the power switch of the
control box while pulling the trigger (with the
blades closed)

∗

While the blades are closed, check that the
lamp of the shears is turned off.

7. Pruning method

(Fig. AM) When pruning, cut twigs one by one
between the upper and lower blades.
(This machine can cut twigs with a diameter of
up to approximately 30 mm. When the opening
angle of the blades is changed, the diameter can
be up to about 15 mm.)

∗

If the battery charge level is low, the ma-
chine may not be able to cut twigs.

∗

The machine may not be able to cut twigs,
depending on the dryness of the wood or
other factors.

When stopping work, lock the trigger lock lever
with the blades closed or turn off the power
switch of the control box, and then store the
shears in the holster.

∗

If the machine is not used for five minutes,
it is set in the standby mode automatically.
When starting work again, release the trig-
ger lock lever. Then, hold down the switch
lever. After the buzzer sounds, you can re-
start pruning work.

∗

If the machine is not used for 60 minutes,
the power is turned off automatically.

∗

When starting the work again, turn the
switch off, and then turn it on again. Then,
hold down the switch lever. After the buzz-
er sounds, you can re-start pruning work.

When you have finished pruning, turn off the
power of the control box with the blades closed,
disconnect the connecting cable, remove the
battery pack from the control box, fit the pack cap
to the battery pack, and store the machine in a
dry location that is not affected by high tempera-
ture and that is away from children.

WARNING

•

When storing the shears in the holster,
be sure to close its blades.

If the machine is stored while its blades are
open, you may be injured and the holster
may be broken.

∗

If the trigger lock lever is locked with the
trigger pulled (with the blades closed),
the blades are kept closed even if the
trigger is released after that.
To open the blades again, release the
trigger lock lever while depressing the
trigger and switch lever.

WARNING

•

Use safety glasses.

Wear safety glasses when using the ma-
chine. Otherwise you run the risk of eye
damage due to flying chips.

PASJ30.book 22 ページ２０１１年１２月９日　金曜日　午後２時１１分

«
...
20
21
22
23
24
...
»

Содержание PASJ30(CE)





























Отзывы:

Нет отзывов