manualshive.com logo in svg

Matrox Solios eA, Установка и справочник по оборудованию, Страница: 41 / 196

Поделиться
Скачать
Matrox Solios eA Скачать руководство пользователя страница 41

 Connecting video sources      41

Connect the cable’s DVI connector to one of the DVI connectors on Matrox Solios 
eA/XA. Then, connect the BNC connectors as follows.

Important

To connect the output of a display board (with a DVI output connector) to the 
analog video input connectors, you can use a standard cable (DVI-I to DVI-I or 
DVI-A to DVI-A cable) if the display board encodes the synchronization signals 
on the video data (sync on green). Otherwise, you must use the Matrox 
DVI-TO-8BNC/O cable or a custom cable that re-routes the synchronization 
signals to the appropriate pins.

Connecting to Matrox Solios GigE

The Matrox Solios GigE board has the following connectors:

•

Four Ethernet connectors (on the bracket).

 Used to receive video input from 

GigE Vision-compliant video sources and transmit/receive communication signals 
between the video source and the frame grabber. Can also be used to receive data 
from and transmit data to other types of Ethernet devices.

•

Internal auxiliary I/O connector (30-pin).

 Used to transmit timing and 

synchronization signals, and transmit/receive auxiliary signals. The connector is 
located on the edge of the board, making the signals accessible from inside the 
computer enclosure.

BNC label

1

,

2

Signal on DVI connector 0

Signal on DVI connector 1

Expected input, with respect to the DVI 
connector.

VID IN 0

P0_VID_IN_A

P0_VID_IN_B

Video input A or B for path 0 (monochrome or 
red input).

VID IN 1

P1_VID_IN_A

P1_VID_IN_B

Video input A or B for path 1 (monochrome or 
green input). 

TRIG 0/2

P0_TTL_AUX(TRIG)_IN

P2_TTL_AUX(TRIG)_IN

TTL trigger input for PSG  0 or 2.

EXP 0/2

P0_TTL_AUX(EXP)_OUT

P2_TTL_AUX(EXP)_OUT

TTL exposure output for PSG 0 or 2.

VID IN 2

P2_VID_IN_A

P2_VID_IN_B

Video input A or B for path 2 (monochrome or 
blue input).

VID IN 3

P3_VID_IN_A

P3_VID_IN_B

Video input A or B for path 3 (monochrome 
input).

TRIG 1/3

P1_TTL_AUX(TRIG)_IN

P3_TTL_AUX(TRIG)_IN

TTL trigger input for PSG 1 or 3.

EXP 1/3

P1_TTL_AUX(EXP)_OUT

P3_TTL_AUX(EXP)_OUT

TTL exposure output for PSG 1 or 3.

1. Note that only VID IN 0, TRIG 0, and EXP 0 can be used with Matrox Solios eA/XA Single since there is only one acquisition path (P0).
2. Note that only VID IN 0 and 1, TRIG 0 and 1, and EXP 0 and 1 can be used with Matrox Solios eX/XA Dual since there are only two acquisition paths (P0 and P1).

Содержание Solios eA





































































































































































































Отзывы:

Нет отзывов