Matrix T7XE-01 Скачать руководство пользователя страница 85

Страница: 85 / 91

10.4 lEvElinG THE TREAdmill

ChapTEr 10: TrEadmill SpECifiCaTioNS aNd aSSEmbly GUidE

oPTionAl lEvElinG ASSEmbly TECHniquES: uSE of SHim oR by AddinG A lEvElinG fooT.

Note: It is extremely important that the levelers are correctly adjusted for proper operation. An unbalanced unit may cause belt misalignment or

other issues. Use of a level is recommended.

Remove the leveling shim provided on the underside of the treadmill. The shim can be found mounted on the underside of the right hand side

rail. Remove the rear foot on the side of the treadmill that is resting low. Install the shim as shown above and return the rear foot.

When installing the optional rear leveling foot accessory, remove the existing rear foot. Replace with new leveling foot and fasten to the frame

using the existing fasteners that held in the half-moon foot.

Содержание T7XE-01




























































































Результаты поиска

Содержание T7XE-01

Отзывы:

Похожие инструкции для T7XE-01

Бренды по названию

Популярные бренды

Matrix T7XE-01, Руководство по обслуживанию

Результаты поиска

Содержание T7XE-01

Отзывы:

Похожие инструкции для T7XE-01

Бренды по названию

Популярные бренды