Matrix T7XE-01 Скачать руководство пользователя страница 7

Страница: 7 / 91

CaUTioN

: If you experience chest pain, nausea, dizziness or short-

ness of breath, STOP exercising immediately and consult a physi-

cian before continuing.

• Donotusetheequipmentinanywayotherthandesignedorintendedby

the manufacturer. It is imperative that all Matrix Fitness Systems equip-

ment is used properly to avoid injury.

• Keephandsandfeetclearofmovingpartsatalltimestoavoidinjury.

• Unsupervisedchildrenmustbekeptawayfromthisequipment.

• Donotwearlooseclothingwhileonequipment.

ChapTEr 2: imporTaNT SafETy iNSTrUCTioNS

2.3 REAd And SAvE THESE inSTRuCTionS

This treadmill is intended for commercial use. To ensure your

safety and protect the equipment, read all instructions before

operating the MATRIX T7xe-01 treadmill.

When using an electrical product, basic precautions should always

be followed including the following:

daNGEr

: To reduce the risk of electric shock: Always unplug this

equipment from the electrical outlet immediately after using and

before cleaning.

WarNiNG:

To reduce the risk of burns, fire, electrical shock or

injury to persons that may be associated with using this product.

An appliance should never be left unattended when plugged in. Unplug

from the outlet when not in use and before putting on or taking off parts.

This product must be used for its intended purpose described in this ser-

vice manual. Do not use other attachments that are not recommended

by the manufacturer. Attachments may cause injury.

To prevent electrical shock, never drop or insert any object into any open-

ing.

Do not remove the console covers. Service should only be done by an

authorized service technician.

Neveroperatethetreadmillwiththeairopeningblocked.Keeptheair

opening clear, free of lint and hair.

Never operate product if it has a damaged cord or plug, if it is working

improperly, if it has been damaged, or immersed in water.

Do not carry this unit by its supply cord or use the cord as a handle.

Keepanypowercordawayfromheatedsurfaces.

Close supervision is necessary when the treadmill is used by or near

children or disabled persons.

Do not use outdoors.

Do not operate where aerosol (spray) products are being used or when

oxygen is being administered.

To disconnect, turn all controls to the off position, then remove plug from

the outlet.

Connect this treadmill to properly grounded outlets only.

Содержание T7XE-01




























































































Результаты поиска

Содержание T7XE-01

Отзывы:

Похожие инструкции для T7XE-01

Бренды по названию

Популярные бренды

Matrix T7XE-01, Руководство по обслуживанию

Результаты поиска

Содержание T7XE-01

Отзывы:

Похожие инструкции для T7XE-01

Бренды по названию

Популярные бренды