Matrix R3xm Скачать руководство пользователя страница 11

11

BEFORE YOU BEGIN

LOCATION OF THE UNIT

Place the equipment on a level and stable surface away from 

direct sunlight. The intense UV light can cause discoloration on the 

plastics. Locate your equipment in an area with cool temperatures 

and low humidity. Please leave a clear zone on both sides of the 

equipment that is at least 24” (600 mm). This zone must be clear 

of any obstruction and provide the user a clear exit path from 

the machine. Do not place the equipment in any area that will 

block any vent or air openings. The equipment should not be 

located in a garage, covered patio, near water or outdoors.

LEVELING THE EQUIPMENT

The equipment should be level for 

optimum use. Once you have placed 

the equipment where you intend to 

use it, raise or lower one or both of 

the adjustable levelers located on the 

bottom of the frame. Use 6mm hex key 

through the access hole (shown below).
A carpenter’s level is recommended. 
NOTE: There are only two 

levelers on the equipment.

WARNING!

Our equipment is heavy, use care and additional help if necessary when 

moving. Failure to follow these instructions could result in injury.

POWER

If the equipment is powered by a power supply, the power must 

be plugged into the power jack, which is located in the front 

of the equipment near the stabilizer tube. Some equipment 

has a power switch, located next to the power jack. Make sure 

it is in the ON position. Unplug cord when not in use.

WARNING!

Never operate equipment if it has a damaged cord or plug, if it is 

not working properly, if it has been damaged, or immersed in water. 

Contact Customer Tech Support for examination and repair.

PROPER USAGE

1.  Sit on the R3xm facing the console. 

Both feet should be on the floor 

one on each side of the frame. 

2.  To determine proper seat position, sit 

on the seat and position the ball of your 

foot on the center of the pedal. Your 

knee should bend slightly at the furthest 

pedal position. You should be able to 

pedal without locking your knees or 

shifting your weight from side to side.

3.  Adjust pedal straps to desired tightness.

4.  To get off of the R3xm, follow the 

proper usage steps in reverse.  

Note: Matrix R3xm is speed independent.

TRAINING AREA

2 M

(78.7”)

1.5 M

(59.2”)

0.7 M

(27”)

FREE AREA

2.5 M

(98.4”)

2.7 M

(106.4”)

1.9 M

(74”)

Содержание R3xm

















Отзывы: