Matrix Fitness PCTV Скачать руководство пользователя страница 50

Страница: 50 / 66

On Screen Installer:

The PCTV screen, by default, will always start up in the Install Application until the install process (via the steps in the application) is complete

to ensure each device is properly configured at the installation. The installation application contains four views to lead the installer though

configuring the screen.

1. Welcome Screen.

2. Default Settings (language, unit type, etc).

3. Network Selection (wired, wireless, no network) and authentication.

4. TV Channel Scanning.

After the install application has been successful completed, the PCTV screen will start in normal mode. After installation, the settings can be

accessed by entering the screen touch sequence and code as detailed in the above Settings / Set-up mode.

Screen Configuration Wizard:

The configuration wizard takes a user through the steps to install the features of the PCTV Screen. These features will let club members view

TV, video on demand, and gather statistics of their workouts. After configuring the PCTV Screen, The PCTV must be tested it to ensure all the

features are working properly.

After it is confirmed that the PCTV Screen is working correctly, complete the installation.

Prerequisites

Before using this configuration wizard, each PCTV Screen should be cabled as described in Chapter 3 with the following:

• If wired: Cat 5e / Cat 6 Ethernet wiring for video on demand.

• If wireless: Wireless USB / card connected to Access Point.

• Coaxial cable for TV viewing.

• C-SAFE cable.

Tasks

Once power is connected to the system, the system will boot up.

Perform the following:

• Connect (pair) the PCTV Screen with the Gateway and the back end server, so that media can be downloaded to the PCTV Screen and

workout statistics can be stored for users.

• Install and configure the TV tuner so users can watch TV shows on the PCTV screen.

• Test the unit to ensure the TV and video on demand work correctly.

• Ensure the unit gathers workout statistics.

• Complete the installation of the unit by ensuring proper cable routing and secure the back panel.

4.2 INStALLAtIoN

PRoGRAMMING tHE PCtV

Содержание PCTV



































































Результаты поиска

Содержание PCTV

Отзывы:

Похожие инструкции для PCTV

Бренды по названию

Популярные бренды

Matrix Fitness PCTV, Руководство по обслуживанию

Результаты поиска

Содержание PCTV

Отзывы:

Похожие инструкции для PCTV

Бренды по названию

Популярные бренды