background image

9

83

16    

 A1   

18    

 15                         

A2

C

D

H

min

max

 A1           A2

   H              D

  15           18

  16           C

Un

max

 A1           A2

   H              D

  15           18

  16           C

Un

t

t

t

t

HRH-5

8595188136396

Indication of supply voltage
Choice of function

Function PUMP UP                                                                     Function PUMP DOWN

Relay is designed for monitoring levels in wells, basins, reservoirs, tanks...
In one device you can choose the following confi gurations:
- one-level switch of conductive liquids (by connecting H and D)
- two-level switch of conductive liquids
One-state device monitors one level, two-state device monitors two levels (switches on one level 
and switches off  on another level)
Choice of function PUMP UP, PUMP DOWN
Adjustable time delay on the output (0.5 - 10s)
Sensitivity adjustable by a potentiometer (5-100kΩ)
Measuring frequency 10Hz prevents polarization of liquid and raising oxidation of measuring probes
Galvanically separated supply voltage UNI 24.. 240 VAC/DC
Output contact 1xchangeover/SPDT  8A/250V AC1
1-MODULE, mounting onto a  DIN rail

Level switch 

HRH-5

Monitoring of two levels    

2

A1 - A2

24... 240 V AC/ DC (AC 50 - 60 Hz)

max. 2 VA

-15 %; +10 %

adjustable in range 5 kΩ -100 kΩ

max. AC 3.5 V

AC <0.1 mA

max. 400 ms

800 nF (sensitivity 5kΩ), 100 nF (sensitivity 100 kΩ)

adjustable, 0.5 -10 sec

1.5 sec

± 5 %

1x changeover/ SPDT (AgNi / Silver Alloy )

8 A / AC1

2500 VA , 240 W 

250 V AC1 / 24 V DC

500 mW

1x10

7

1x10

5

-20 °C to +55 °C (-4 °F to 131 °F)

-30 °C to +70 °C (-22 °F to 158 °F)

3.75 kV (supply - sensors)

any

DIN rail EN 60715

IP 40 from font panel / IP 10 terminals

III.

2

AWG 10 (2.5 mm2)

90 x 17.6 x 64 mm (3.5˝ x 0.7˝ x 2.5˝)

72 g (2.5 oz.)                       

 EN 60255-6,  EN 61010-1

 see pg. 90-91

Functions:
Supply terminals:
Voltage range:
Input:
Toleration of voltage range:
Measuring circuit
Sensitivity ( input resistance):
Voltage n electrodes:
Current in probes:
Time response:
Max. capacity of probe cable:
Time delay (t):
Time delay after switching on (t1):
Accuracy
Accuracy in setting (mechanical):
Output
Number of contacts:
Current rating:
Switching voltage:
Switched voltage:
Min. switched output DC:
Mechanical life (AC1):
Electrical life:
Other information
Operational temperature:
Storing temperature:
Electrical strenght:
Operational position:
Mounting:
Protection degree:
Overvltage category:
Pollution degree:
Profi le of connecting wires (mm

2

):

Dimensions:
Weight:
Standards:
Recommended measuring probes:

Connection

Function

Device description

Technical parameters

Tank with

 monitored level

Relay is designated for monitoring of levels of conductive liquids with possibility of functions: PUMP UP 

or PUMP DOWN. To prevent polarization and liquid electrolysis of liquid, and undesirable oxidation of 

measuring probes, alternating current is used. For measuring use three measuring probes: H- upper level, 

D-  lower level, C - common probe. In case you use a tank made of a conductive material, you can use 

it as probe C. In case you require monitoring of one level only, it is neccessary to connect inputs H and 

D and connect them to one probe - in this case sensitivity is lowered by half  (2.5... 50kΩ). Probe C can 

be connected with a protective wire of supply  system (PE). To prevent undesirable switching out output 

contacts by various infl uences (sediment on probes, humidity...) it is possible to set sensitivity of the device 

according to conductivity of monitored liguid (corresponding to “resistance” of liquid) range 5 up to 100kΩ. 

To reduce infuences of undesirable switching of output contacts by liquid gorgle in tanks, it is possible to set 

delay of output reaction 0.5 - 10s.

Symbol

!

!

!

!

!

!

!

!

!

!

Monioring of one level   

Un

max

level

min

15-18

red LED

Un

max

level

min

15-18

red LED

Tank with 

monitored level

     Supply voltage terminals

Terminals for conection of 

probes H, D

Output indication

Choice of function

Adjustment of 

delay on output

  Terminal for connection of 

probe C

Output contacts

EAN code

HRH-5 /UNI

Содержание FPC-30020-CON













Отзывы: