Matco Tools MCL20RG Скачать руководство пользователя страница 7

MCL20RG 

rev. 05/11/20

MCL20RG 20V+ 1/4" Brushless Rivet Gun

SAVE THESE INSTRUCTIONS!

SAFETY INSTRUCTIONS FOR BATTERY 

CHARGER AND BATTERY PACK

DANGER! READ CAREFULLY
120 Volts present at charging terminal. Absolutely DO NOT 
probe with conductive objects.

1.   CAREFULLY READ AND UNDERSTAND THESE 
INSTRUCTIONS

 

This manual contains critical safety and operating instructions 
for the tool, battery charger, and battery .
2 .   Before using battery charger, read all instructions and 
cautionary markings on (1) battery charger, (2) battery, and (3) 
product using battery .
3 .  

CAUTION

 - To reduce risk of injury, charge only MATCO 

rechargeable batteries marked on the charger label . Other 
types of batteries may burst causing personal injury and 
damage .
4 .   Do not expose charger to rain or snow .
5 .   Use of an attachment not recommended or sold by Matco 
or the battery charger manufacturer may result in a risk of fire, 
electric shock, or injury to persons .
6 .   To reduce risk of damage to electric plug and cord, pull by 
plug rather than cord when disconnecting charger .
7 .   Make sure cord is located so that it will not be stepped on, 
tripped over, or otherwise subjected to damage or stress .
8 .   An extension cord should not be used unless absolutely 
necessary . Use of improper extension cord could result in a 
risk of fire and electric shock . If extension cord must be used, 
make sure:

a .  That pins on plug of extension cord are the same 
number size, and shape as those of plug on charger;
b .   That extension cord is properly wired and in good 
electrical condition;
c .   That wire size is at least as large as the one specified 
in the table below .

Table 1: RECOMMENDED MINIMUM AWG SIZE FOR 
EXTENSION CORDS FOR BATTERY CHARGERS

Length of Cord (Feet)  

25   50   75   100  150

AWG Size of Cord  

18   18   16   14    12

9 .  

Do not operate charger with damaged cord or plug - 

replace them immediately.

10 .  Do not operate charger if it has received a sharp blow, 
been dropped, or otherwise damaged in any way; take it to a 
MATCO AUTHORIZED service facility .
11 .  Do not disassemble charger or battery cartridge; take it to 
your MATCO AUTHORIZED distributor service facility . Incorrect 
reassembly may result in a risk of electric shock or fire .

12 .  To reduce risk of electric shock, unplug charger from 
outlet before attempting any maintenance or cleaning . Turning 
off controls will not reduce this risk .
13 .  The battery charger is not intended for use by young 
children or infirm persons without supervision .
14 .  Young children should be supervised to ensure that they 
do not play with the battery charger .

OPERATIONAL GUIDELINES FOR BATTERY 

CHARGER AND BATTERY PACK

1 .   Do not attempt to use a step-up transformer, an engine 
generator or DC power receptacle .
2 .   Do not allow anything to cover or clog the charger vents .
3 .   Always cover the battery terminals with the box or cover 
when the battery cartridge is not used .
4 .   Do not short the battery cartridge:

(1)   Do not touch the terminals with any conductive 
material .
(2)  Avoid storing battery cartridge in a container with 
other metal objects such as nails, screws, coins, etc .
(3)   Do not expose battery cartridge to water or rain . A 
battery short can cause a large current flow, overheating, 
possible burns and even a breakdown .

5 .   Do not store the tool and Battery Cartridge in locations 
where the temperature may reach or exceed 50°C (122°F) .
6 .   Do not incinerate the Battery Pack even if it is severely 
damaged or is completely worn out . The battery cartridge can 
explode in a fire .
7 .   Be careful not to drop, shake or strike battery as it will 
affect the capacity and may void warranty .
8 .   Do not charge inside a box or container of any kind . The 
charger and battery are ventilated devices and must NOT be 
placed next to a heat source or in exposure to radiating heat . 
9 .  Place charger on a solid and sturdy surface as there are 
vents on the bottom side of the charger .
10 .  Always unplug the charger from the power supply when a 
charging sequence is not taking place . 

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.

WARNING

Содержание MCL20RG

























Отзывы: