background image

The floor pad packed with this burnisher

MUST BE

attached to pad driver before

operating the unit. 

DO NOT OPERATE

the burnisher pad

driver without the pad securely in place
to avoid damage to the floor and/or
burnisher.

To Install Pad:

1)

Remove center cut-out from the

floor pad

2)

Tilt burnisher back on rear wheel

and unscrew center lock clamp pad
retainer by turning counterclockwise in

"OPEN"

position.

3)

Center pad on center lock clamp or

collar with hair side down for optimum
finish.

4)

Secure the pad to pad driver by turn-

ing the center lock clamp clockwise in
the

"CLOSE"

position until it is locked in

position.

F

LOOR

P

AD

I

NSTALLATION

H

ANDLE

A

SSEMBLY

I

NSTRUCTIONS

C

ARE

&

M

AINTENANCE

This burnishers is shipped without the
handle attached to the chassis. Handle
hardware kit (#372811) contains the
necessary parts to attach the handle to
the burnisher.

1)

Remove burnisher chassis and han-

dle assembly for the carton.

2) 

Using screws #353272 and nuts

#354791, insert one screw into each
hole and secure with nuts on opposite
side of handle tube. 

DO NOT

over-tight-

en nuts, this will deform the handle
tube.

3)

Slide the handle assembly over han-

dle "T" on the chassis making sure the
line cord is towards back of burnisher
and loosen handle clamp.

4)

Remove speed- pin (A) from clevis.

Line up strut with clevis and insert
speed-pin (A) thru clevis and strut.

1)

After each use, wipe off all polished

and painted areas with a clean cloth.

2)

Check all bolts and screws at the

switch box, handle and wheels. Tighten
if they are loose and replace any that
are broken. 

3) 

Unplug burnisher and check power

cord for any breaks in the wire. Breaks
will most likely occur near the plug or
switch. Any breaks should be repaired
or replaced immediately.

4)

When the burnisher is not in use,

remove buffing pad, unplug power cord
and wrap it around the cord hook.
Store in a dry area.

P

AGE

2

Содержание MBS-1500







Отзывы: