background image

C

ARE AND

M

AINTENANCE

This burnisher requires limited maintenance
for proper operation and years of service.

1)

After each use, wipe off all of the polished

and painted areas with a clean cloth.

2)

Check all bolts and screws at the switch

box, handle and wheels. Tighten if they are
loose and replace any that are broken. 

3)

Unplug burnisher and check power cord

for and breaks in the wire.  Breaks will most
likely occur near the plug or switch. Any
breaks should be repaired or replaced
immediately.

4)

When the burnisher is not in use, remove

buffing pad, unplug power cord and wrap it
around the cord  hooks. Store in a dry area. 

T

ROUBLE

S

HOOTING

G

UIDE

PROBLEM: 

Not polishing floor to high luster.

POSSIBLE CAUSE: POSSIBLE 

SOLUTION:

1)

Improperly prepared floor or

1)

Refinish floor.

floor needs refinishing.

2)

Buffing pad is flattened from

2)

Replace with new 1" buffing pad.

unit sitting on pad.

3)

Hard glazed surface on pad.

3)

Replace with new 1" buffing pad.

4)

Pad used on wet surface or

4)

Replace with new 1" buffing pad.

clogged with dirt.

5) 

Pad too thin.

5)

Replace with new 1" buffing pad.

6)

Burnisher out of adjustment,

6)

Have a certified technician adjust rear wheels.

rear wheels shifted.

PROBLEM: 

pulling to one side or skipping sideways.

POSSIBLE CAUSE:

POSSIBLE SOLUTION:

1)

Buffing pad too thick for

1)

Replace with 1" buffing pad.

machine setting.

2)

Rear wheels are out of adjustment.

2)

Have a certified technician adjust rear wheels.

PROBLEM: 

Machine not running.

POSSIBLE CAUSE: 

POSSIBLE SOLUTION

1)

Defective power cord.

1)

Contact Manufacturer or Service Center.

2)

Defective switch.

2)

Contact Manufacturer or Service Center.

3)

Defective motor. 

3)

Contact Manufacturer or Service Center.

4)

Motor unplugged from handle cord.

4)

Plug motor lead into handle cord receptacles.

Burnisher Manual - Part No 344249 Rev A - Printed in USA 05/12/06

P

AGE

4

®

777 South Street, P.O. Box 2310, Newburgh, NY 12550-0606

TEL:  

(800) 835-7812 

W

(845) 565-8850

FAX: 

(800) 752-6883 

W

(845) 565-9392

Internet Access:

www.mastercraftusa.com

W

[email protected]

Содержание MBS-1500







Отзывы: