MasterCraft Maximumu 055-6701-6 Скачать руководство пользователя

Страница: 11 / 17

CUTTING 5

-7

(12.7-17.8 cm) WIDE

WORKPIECES

The vise is set up at the factory for
cutting workpieces up to 5

(12.7 cm) in

width. This is the preferred set-up. If it is

necessary to cut workpieces between

(12.7-17.8 cm) in width, the mitre

gauge will have to be relocated on the

chop saw base.

1. Remove the front and rear mitre

gauge cap screws (1) using the 17 mm

wrench supplied.

2. Move the mitre gauge (2) back

approximately 1½

(3.81 cm) until the

hole and slot in the mitre gauge line

up with the next two holes (3) in the

chop saw base.

3. Reinstall and tighten the mitre gauge

cap screws in the two new holes (4).

OPERATING THE VISE QUICK-
RELEASE

The vise has a quick-release feature that

allows for making major adjustments

much quicker.

1. To operate the quick-release system,

turn the vise adjustment handle (1)

counter-clockwise two or three turns

to loosen the vise jaws.

2. Lift upward on the front of the quick-

release nut (2) to release the vise

screw (3).

3. While holding the quick-release nut

upward in the released position, pull

the vise adjustment handle toward

you to quickly open the vise.

4. To quickly close the vise, release the

quick-release nut and push the crank

away from you.

5. Use the crank to completely tighten

the vise on the workpiece.

ON/OFF SWITCH

To turn the chop saw On, squeeze the

switch trigger (1) until the chop saw

starts. To turn the chop saw Off, release

the switch trigger.

REPLACING THE CUT-OFF DISC

The cut-off disc must be replaced when it

has become damaged in any way or it has

worn down to a diameter of less than

(25.4 cm).

NOTE:

To cut workpieces between 7-9

(17.8-22.9 cm) in width, locate the mitre gauge in

the back two holes (4) in the chop saw base.

WARNING!

Always make sure the workpiece is flat

against the chop saw base and securely

held in the vise before turning the saw On.

WARNING!

Always make sure the cut-off blade is NOT

touching the workpiece when the switch is

being turned On. Let the motor come to full

speed before beginning to cut.

WARNING!

Disconnect your chop saw from the power

source before attempting to change the

cut-off blade.

model no. 055-6701-6 contact us 1-800-689-9928

OPERATING INSTRUCTIONS

Содержание Maximumu 055-6701-6


















Результаты поиска

Содержание Maximumu 055-6701-6

Отзывы:

Похожие инструкции для Maximumu 055-6701-6

Бренды по названию

Популярные бренды

MasterCraft Maximumu 055-6701-6, Инструкция по эксплуатации

Результаты поиска

Содержание Maximumu 055-6701-6

Отзывы:

Похожие инструкции для Maximumu 055-6701-6

Бренды по названию

Популярные бренды